2020 April

3KW 220V Swimming Pool Thermostat & SPA Heater Electric Water Heater Equipment

This thermostat is designed specifically for the hot tub, the thermostat is installed in the pipeline jacuzzi. When adding a hot water bath, start the pump, the thermostat automatically heat insulation work, so the water temperature bath maintained at 39 degrees Celsius, give your Jacuzzi to create a more comfortable environment. Input voltage:220V 2. Current:13.6A 4. The initial set temperature settings: COASTS equipped with ultra-high temperature protection thermostat switch, thermostat to limit overheating and protect users against danger, however, users should be done after the installation is complete, the first under the premise of safety checks to ensure that the operation of the thermostat’s normal function, By using the tub filled with water to a suitable level and start the system automatically checks and let the system run until the thermostat temperature stabilized at the highest level and display lights go out, use an accurate thermometer to measure the water temperature should be at 40 Celsius. COASTS thermostat operation is fully automated, clockwise, the heating is on, indicator light, the temperature reaches a preset temperature, will remain at that temperature. The thermostat can be maintained within a temperature not exceeding 40 Celsius (104 Celsius) range. If cold water is started, will be 6 8 Celsius / h elevated temperatures. Automatic heating: thermostat will first reach the preset temperature, then stop working until the temperature dropped a few degrees, the thermostat automatically turns on. Ultra-high temperature (over 49), ultra-high temperature switch will automatically trip (power off). COASTS thermostat outlet to the bathtub in the middle of the pipe or valve or check valve cannot be installed. 1 x 3KW 220V Swimming Pool Thermostat. We are not responsible for undeliverable address. The item “3KW 220V Swimming Pool Thermostat & SPA Heater Electric Water Heater Equipment” is in sale since Friday, June 7, 2019. This item is in the category “Home & Garden\Yard, Garden & Outdoor Living\Pools & Spas\Pool Equipment & Parts\Pool Heaters & Solar Panels”. The seller is “maxx.plus” and is located in Ontario, California. This item can be shipped to United States.

Power Source: Electric
MPN: Does Not Apply
Brand: Unbranded
Input voltage: 220V

Fibropool FH 220 Swimming Pool Heater Heat Pump Refurbished scratch and dent

Compact, lightweight 20,000 BTU/hr Heat pump for Small pools and Spas. Above Ground pools up to 18′ Round. 240 volts-60HZ USA voltage Heat and cool modes. Highest efficiency in the industry 6.20 COP. Union connectors are included for 1 1/2 pvc plumbing. Foot print: 36″ x16″, weighs 100lbs. 20 Amps, 240 v circuit, with double Pole breakers. The item “Fibropool FH 220 Swimming Pool Heater Heat Pump Refurbished scratch and dent” is in sale since Saturday, April 25, 2020. This item is in the category “Home & Garden\Yard, Garden & Outdoor Living\Pools & Spas\Pool Equipment & Parts\Pool Heaters & Solar Panels”. The seller is “ydomarine” and is located in Waveland, Mississippi. This item can be shipped to United States.

Modified Item: No
Brand: Fibroheat
Model: FH 020
Power Source: Electric
Custom Bundle: No
MPN: 4336594718

Hayward W3H250FDN Universal H-Series 250,000 BTU Pool and Spa Heater Natural Gas

Pool Chemicals & Testing. Spa Chemicals & Sanitizers. Sign up to receive special insider notifications of deals, promotions, and new items! Hayward W3H250FDN Universal H-Series 250,000 BTU Pool and Spa Heater Natural Gas. The Hayward Universal H-Series 250,000 BTU Natural Gas Heater delivers premium heating performance for years of reliable, long-lasting comfort. A durable cupro nickel heat exchanger offers exceptional protection against corrosion and premature failure caused by unbalanced water chemistry. Industry-leading hydraulic design reduces circulation pump run time to provide major energy savings. Front-panel-only access and intuitive control pad provide easy operation, service and maintenance. Low NOx emissions meet air quality standards in all low-NOx areas, ensuring low environmental impact. Questions about this item? To make sure we get the order to you as fast as possible, orders are processed as soon as they come in. We cannot guarantee that any order can be cancelled once placed and processed. Included in this but not limited to are Heat Pumps, Gas Heaters, Large Filters, Slides, and Diving Boards. These products are delivered to the front of the driveway, not to the garage or installation site. The trucking company is not responsible to transport your items anywhere other than the front of your driveway. In this circumstance, we will call you with the additional charges. To help make this process as smooth as possible please follow these guidelines. Sign Bill of Lading (receiving bill). This document says that the order has been received. This all states that the order has arrived in good condition. It is the customer’s responsibility to inspect all packages received. This document also states the number of cartons you are receiving, please make sure this number is the same as the actual number of cartons received. It is your responsibility to make sure your order is in good condition upon receipt. Backyard Pool Superstore is here for all of your pool and backyard needs. Here at Backyard Pool Superstore, we understand that mistakes can be made. The packaging must be resealed with. See below for more details. When you sign for the product, you state the product arrived in good condition, and you accept the condition it was delivered in. Our staff is dedicated to making sure your experience with us is not only good, but the best! We are not just “Internet retailers”, we are pool and backyard professionals that have been in business for over 20 years. We pride ourselves on fast, professional customer service. We use the latest technology to assist you with your pool, spa, patio, and backyard needs. The Best Customer Service and Expert Advice. With many years of experience in all aspects of the pool and backyard industry, we are here to help you with all of your questions. If one of our staff members cannot help you immediately, we will not rest until we find an answer to your question. The item “Hayward W3H250FDN Universal H-Series 250,000 BTU Pool and Spa Heater Natural Gas” is in sale since Wednesday, January 29, 2020. This item is in the category “Home & Garden\Yard, Garden & Outdoor Living\Pools & Spas\Pool Equipment & Parts\Pool Heaters & Solar Panels”. The seller is “backyardpoolsuperstore” and is located in Multiple Locations. This item can be shipped to United States.

Brand: Hayward
MPN: W3H250FDN
Power Source: Natural Gas
Model: W3H250FDN
Country/Region of Manufacture: United States

Swimming Pool Electric SPA Heater Heating Thermostat 3KW Fix Temperature 220V

You may also like. Swimming Pool Electric SPA Heater Heating Thermostat 3KW Fix Temperature 220V. Description: This thermostat is designed specifically for the hot tub, the thermostat is installed in the pipeline jacuzzi. When adding hot water bath, start the pump, the thermostat automatically heat insulation work, so the water temperature bath maintained at 39 degrees Celsius, give your Jacuzzi to create a more comfortable environment Feature and operation: 1. The initial set temperature settings: COASTS equipped with ultra-high temperature protection thermostat switch, thermostat to limit overheating and protect users against danger, however, users should be done after the installation is complete, the first under the premise of safety checks to ensure that the operation of the thermostat’s normal function, By using the tub filled with water to a suitable level and start the system automatically checks and let the system run until the thermostat temperature stabilized at the highest level and display lights go out, use an accurate thermometer to measure the water temperature should be at 40 °C 2. COASTS thermostat operation is fully automated, clockwise, the heating is on, indicator light, temperature reaches a preset temperature, will remain at that temperature 3. The thermostat can be maintained within a temperature not exceeding 40 °C (104 °F) range. If cold water is started, will be 6 8 °C / h elevated temperatures 4. Automatic heating: thermostat will first reach the preset temperature, then stop working until the temperature dropped a few degrees, the thermostat automatically turns on 5. Ultra-high temperature (over 49 °C), ultra-high temperature switch will automatically trip (power off) Parameter: 1. Input voltage:220V 2. Current:13.6A 4. Weight:3.5kg Note: COASTS thermostat outlet to the bath tub in the middle of the pipe or valve or check valve can not be installed. 1 x 220V 3KW SPA Heater. We are not responsible for undeliverable address. If there have any question, please feel free tell us. We will do our best to help you. The item “Swimming Pool Electric SPA Heater Heating Thermostat 3KW Fix Temperature 220V” is in sale since Thursday, March 22, 2018. This item is in the category “Home & Garden\Yard, Garden & Outdoor Living\Pools & Spas\Pool Equipment & Parts\Pool Heaters & Solar Panels”. The seller is “function-e.mall” and is located in Shenzhen. This item can be shipped worldwide.

Power Source: Electric
MPN: Does Not Apply
Brand: Unbranded

GAME 4721 SolarPRO Curve Solar Pool Heater for Above-Ground and Inground Pools

GAME 4721-BB SolarPRO Curve Solar Pool Heater, Made for Intex & Bestway Above-Ground and Inground Pools, Includes Intex Adapters, 2 Hoses & Clamps. SOLAR POOL HEATER: The GAME SolarPRO Curve Solar Pool Heater has been designed for above-ground and most inground pools. It increases the pool temperature by 5 degrees in 4 days (for an 8,000-gallon pool). DURABLE CONSTRUCTION: We’ve designed this above-ground solar pool heater with high-quality materials that will hold up against frequent exposure to the sun and outdoor elements. UNIQUE CURVED SHAPE: The GAME solar pool heater has been engineered with a unique curved shape that maximizes heat collection. The treaded ports have been added for versatile plumbing options. ADJUSTABLE LEGS: This solar heater is compatible with Intex, Bestways, and most above and inground pools. The adjustable and foldable legs allow the heater to be set for maximum exposure to the sun, along with a clear cover that locks in heat. THE PERFECT GRADUAL HEATER: This solar pool heater is not intended to be a miracle-cure heater. It’s designed to extend your pool season by gradually increasing the water temperature by a few degrees. Maximum heat output with space saving footprint. The item “GAME 4721 SolarPRO Curve Solar Pool Heater for Above-Ground and Inground Pools” is in sale since Friday, April 24, 2020. This item is in the category “Home & Garden\Yard, Garden & Outdoor Living\Pools & Spas\Pool Equipment & Parts\Pool Heaters & Solar Panels”. The seller is “shengrongmaoyi” and is located in California. This item can be shipped to United States.

MPN: 4721-BB
UPC: 0712910047210
EAN: 0712910047210
Brand: GAME
Model: 4721
Power Source: Solar
Material: Plastic

220V 2KW Electric Water Heater Thermostat Swimming Pool and SPA Heating Heater

You may also like. 220V 2KW Electric Water Heater Thermostat Swimming Pool and SPA Heating Heater. This thermostat is designed specifically for the hot tub, the thermostat is installed in the pipeline jacuzzi. When adding hot water bath, start the pump, the thermostat automatically heat insulation work, so the water temperature bath maintained at 39 degrees Celsius, give your Jacuzzi to create a more comfortable environment. The initial set temperature settings: COASTS equipped with ultra-high temperature protection thermostat switch, thermostat to limit overheating and protect users against danger, however, users should be done after the installation is complete, the first under the premise of safety checks to ensure that the operation of the thermostat’s normal function, By using the tub filled with water to a suitable level and start the system automatically checks and let the system run until the thermostat temperature stabilized at the highest level and display lights go out, use an accurate thermometer to measure the water temperature should be at 40 °C 2. COASTS thermostat operation is fully automated, clockwise, the heating is on, indicator light, temperature reaches a preset temperature, will remain at that temperature 3. The thermostat can be maintained within a temperature not exceeding 40 °C (104 °F) range. If cold water is started, will be 6 8 °C / h elevated temperatures 4. Automatic heating: thermostat will first reach the preset temperature, then stop working until the temperature dropped a few degrees, the thermostat automatically turns on 5. Ultra-high temperature (over 49 °C), ultra-high temperature switch will automatically trip (power off). Input voltage:220V 2. Current:13.6A 4. COASTS thermostat outlet to the bath tub in the middle of the pipe or valve or check valve can not be installed. 1 x 220V 2KW SPA Heater. If you have any questions about the product. We will provide you with a good solution and try our best to solve the problem. The item “220V 2KW Electric Water Heater Thermostat Swimming Pool and SPA Heating Heater” is in sale since Saturday, October 12, 2019. This item is in the category “Home & Garden\Yard, Garden & Outdoor Living\Pools & Spas\Pool Equipment & Parts\Pool Heaters & Solar Panels”. The seller is “cjcmall” and is located in Shenzhen. This item can be shipped worldwide.

Power Source: Electric
MPN: Does Not Apply
Brand: Does Not Apply
Power: 2KW
Voltage: 220V

Electric Water Heater Thermostat 3KW Swimming Pool & Bath SPA Hot Tub 50/60Hz

Sign up to Newsletters. 220V 3KW Swimming Pool. Interface Electric Water Heater Thermostat. 220V 3KW Swimming Pool 1.89 Interface Electric Water Heater Thermostat. Thermostat is designed specifically for the needs of the Jacuzzi, the thermostat installed in the bottom of the tub on the massage tub, after adding hot water in the bath, start the water pump, the thermostat automatically heating insulation, the bath water temperature maintained at 30-40 adjustable, it can give your massage bathtub to create a comfortable environment. Thermostat equipped with ultra-high temperature protection thermostat switch, thermostat to limit overheating and protect users against danger, however, users should be done after the installation is complete, the first under the premise of safety checks to ensure that the operation of the thermostat’s normal function, by using the tub filled with water to a suitable level and start the system automatically checks and let the system run until the thermostat temperature stabilized at the highest level and display lights go out, use an accurate thermometer to measure the water temperature should be at 40°C. The operation of the thermostat is fully automatic. When installed properly it will turn ON after user have set the temperature by turning the controlling switch clockwise, then the heating-up indicator turns on. As long as the thermostat is on, it will heat up the water to the user-set level and maintain the temperature. User can turn the controlling switch anticlockwise to a temperature lower than the current water temperature to turn OFF the thermostat, and the heating-up indicator turns off. There is no separate heat controller for user. The 220V/3KW thermostat is designed to efficiently maintain the water temperature of a standard bathtub at the preset level of 40 (104). However, if starting with cold water, the thermostat will increase the temperature at a rate of 6 to 8 (11 to 14) per hour, depending on the initial water temperature, the room temperature, and the size of the bathtub. Once turned ON the thermostat stays ON until the temperature reaches the preset temperature, and then it will turn OFF automatically. It will stay OFF until the temperature drops a few degrees below the preset value, then it will turn back ON. The thermostat continues this ON/OFF cycle for as long as the pump is ON. The indicating lamp is located marks HEATER place. High Temperature Protection/Reset Button. In addition to the regulating thermostat, the thermostat is equipped with a manual reset High Temperature Protection to protect the user against the hazards of high temperatures. In the event of water or the thermostat enclosure reaching temperatures of higher than 49(120) because of blockage or other reasons, the High Temperature Protection will trip(interrupt power) immediately. In order to reset, let the water cool down to approximately 38 (100), then simply push the Reset Button on the top panel. The thermostat should resume operation in the normal manner. The thermostat is equipped with a pressure-sensing switch that protects the thermostat against the hazard of running the system without water. If the water level is low at the beginning or drops low during the operation water pressure is lower than 20KPa (about 2000mmHO2) the pressure sensing switch will interrupt power. Heater can only come ON when the water is at the appropriate level (water pressure is above 20KPa) and the water pump is running. Under no circumstances should any of the outlet (side) ports be closed. Water must flow through both ports when the thermostat is on. At the same time, inlet of heater must be installed perfectly matching to the outlet of water pump to give maximum water flow. Try to ensure that a minimum length of piping is maintained between the thermostat and any opening to the tub. Take off the joint on the outlet/inlet of the thermostat. Glue one side of the joint to the pipe tightly first, then hand tighten the other side to the outlet/inlet of the thermostat. After the installation of the water pump, heater and fitting system, a complete draining must take place, no water is allowed. When using electrical products basic precautions should always be followed, including the following. All electrical connections must be performed by a qualified electrician in compliance with all applicable national and local codes. Danger risk of electric shock connect only to a circuit protected by a Ground-Fault Circuit-Interrupter (GFCI). To prevent the risk of electrocution, check heater for proper ground connection. The thermostat must be properly grounded with a conductor equal to or greater than the power supply conductors. Before making any electrical connection or during installation and service make certain that the electrical power is turned off at the source or circuit breaker and take measures that it CANNOT accidentally be turned on again. Provides the suitable power line according to the thermostat. Connect the provided 220V, 3 wires with grounding branch circuit to a suitable junction box near the thermostat. The power supply should be 220V/50Hz. The blue wire should be connected to L terminal, orange wire should be connected to N terminal and the yellow and green wire should be connected to the ground terminal. Do not allow any electrical appliances (such as lights, telephone, hair dryer, radio or television) in the bathtub, 1.5 meters (5 feet) or less. The thermostat should not be used in salt water, acidic water or alkaline water, can not be used in other places chemically corrosive gases or solvents. Thermostat outlet to the bath tub in the middle of the pipe or valve or check valve can not be installed. This pool thermostat heater should be used with a circulating water pump of 500W or more to work normally. The product is easy to operate, provides a mechanical thermostat switch, you can set the temperature of temperature technology. When the product is safe and reliable movement with the flow switch, over-temperature protection switch. All using mechanical control devices durable economy. Heating thermostat liner material is 316 # stainless steel pipe and electric resistance, corrosion resistance (chlorine corrosion), and durable. The thermostat good interior circulation, not dross, easy removal. The product is small, easy to install in the bathtub at the bottom of the circulating massage pipe. Pipe Dimeter: 1/2.54cm. Size: 340 122 125mm/13.44.85inch. Net Weight: 2kg/4.4lbs. Suitable For: Max 2CBM Hot Tub & Swimming Pool Equipment. We believe that it is our vision and mission to provide innovative products with best service and competitive price to satisfy you. Our goal is to make sure that you can find exactly what you are looking for and make it easy for you to place your orders. California Warehouse: City of Industry, CA. If you need to return, please check twice to confirm the item not work and contact our customer service representative, let us know the detailed problem and send us some pictures for confirmation. Please make sure that item has NO man-made sabotage. Used items will not be accepted for return. All emails will be responded to within. Special circumstances will be listed clearly in the listing. Please do check everything carefully after you received the parcel, any the damage except DOA (Dead-On-Arrival) would not be covered if it’s your fault. A: The item ships from Rancho Cucamonga, CA, United States. A: Please log on your account. Q: How do I return an item? Please contact our customer service before you return an item. The item “Electric Water Heater Thermostat 3KW Swimming Pool & Bath SPA Hot Tub 50/60Hz” is in sale since Wednesday, April 22, 2020. This item is in the category “Home & Garden\Yard, Garden & Outdoor Living\Pools & Spas\Pool Equipment & Parts\Pool Heaters & Solar Panels”. The seller is “technology-etrade” and is located in Rowland Heights, California. This item can be shipped to United States, Canada, Mexico.

Type: Pool Heater
Shape: Pro Shape
Brand: Vevor Pod
MPN: LXQIC002
Model: B-M3-48MM
Country/Region of Manufacture: China
Capacity: Max 2CBM
Material: Metal
Voltage: AC220-240V/50-60Hz
Power: 2.7-3.3KW
Current: 14A
Wire: 3*4 Square millimeter
Pipe Dimeter: 2.54cm/1inch
Size: 340 * 122 * 125mm/13.4*4.8*5inch
Net Weight: 2kg/4.4lbs
Phase Parameters: Single Phase
Suitable For: Hot Tub,Swimming Pool,Jacuzzi,Spa
Package: 1 x Water Heating Thermostat,2 x Interface,1 x Manual
Color: As picture shows
Interface size: 48mm/1.89″

Brand new Pentair Mastertemp 250k 460732 Pool Spa Heater

Brand new Pentair Mastertemp 250k 460732 Pool Spa Heater. Brand new Pentair Mastertemp pool/spa heater. The item “Brand new Pentair Mastertemp 250k 460732 Pool Spa Heater” is in sale since Wednesday, April 22, 2020. This item is in the category “Home & Garden\Yard, Garden & Outdoor Living\Pools & Spas\Pool Equipment & Parts\Pool Heaters & Solar Panels”. The seller is “bronxbabydds” and is located in Orange, California. This item can’t be shipped, the buyer must pick up the item.

Brand: Pentair
Model: MasterTemp
Style: Smooth
Power Source: Natural Gas
Material: Copper
MPN: 460732

Swimming Pool & Bath Tub Water Heater Pressure-Sensing Jacuzzi Easy Install

Sign up to Newsletters. Swimming Pool & Bath SPA Hot Tub Electric Water Heater Thermostat. This listing is to introduce you 5 types of different pool & bath water thermostat. Thermostat is designed specifically for the needs of the Jacuzzi, the thermostat installed in the bottom of the tub on the massage tub, after adding hot water in the bath, start the water pump, the thermostat automatically heating insulation, the bath water temperature maintained at 30-40 adjustable, it can give your massage bathtub to create a comfortable environment. The thermostat can be maintained within a temperature, not exceeding 40 °C (104 °F) range. If cold water is started, there will be 6 8 °C / h elevated temperatures. Thermostat will first reach the preset temperature, then stop working. It won’t automatically turns on until the temperature dropped a few degrees. Ultra-high temperature protection switch and reset button. At the time Ultra-high temperature (over 49 °C) reaches, ultra-high temperature switch will automatically trip (power off). The benefits you can enjoy. The product is easy to operate, with a mechanical thermostat switch for setting temperature. This thermostat provides you safe and reliable movement with the flow switch, over-temperature protection switch. Heating thermostat liner is made of durable 316 stainless steel pipe of electric resistance, corrosion resistance (chlorine corrosion). The thermostat features good interior circulation, not dross, easy removal. Tiny, easy to operate. A mechanical thermostat switch for adjustable temperature. Safe and reliable movement. With flow switch and over-temperature protection switch. Using mechanical control devices-durable, economic. Made of 316 stainless steel, durable, electric resistance, corrosion resistance. With superior interior circulation. Power: 11KW / 2KW / 3KW. Connector size: 48mm(1.89″) / 50mm(1.97″). Wire: 310 mm2 / 34mm2. Suitable for: Hot Tub & Swimming Pool Equipment. 1 x Water Heating Thermostat. 1 x User Manual. We believe that it is our vision and mission to provide innovative products with best service and competitive price to satisfy you. Our goal is to make sure that you can find exactly what you are looking for and make it easy for you to place your orders. California Warehouse: 18501 Arenth Ave, City of Industry, CA 91748. 300 W Airtex Blvd, Suite 200, Houston, TX 77090. 2125 Gateway Blvd, Hebron, KY 41048. 1000 High Street, Perth Amboy, NJ 08861. If you need to return, please check twice to confirm the item not work and contact our customer service representative, let us know the detailed problem and send us some pictures for confirmation. Please make sure that item has NO man-made sabotage. Used items will not be accepted for return. All emails will be responded to within. Special circumstances will be listed clearly in the listing. Please do check everything carefully after you received the parcel, any the damage except DOA (Dead-On-Arrival) would not be covered if it’s your fault. A: The item ships from Rancho Cucamonga, CA, United States. A: Please log on your account. Q: How do I return an item? Please contact our customer service before you return an item. The item “Swimming Pool & Bath Tub Water Heater Pressure-Sensing Jacuzzi Easy Install” is in sale since Tuesday, August 13, 2019. This item is in the category “Home & Garden\Yard, Garden & Outdoor Living\Pools & Spas\Pool Equipment & Parts\Pool Heaters & Solar Panels”. The seller is “qiannlan-3″ and is located in Rowland Heights, California. This item can be shipped to United States, Canada, Mexico.

Brand: VEVOR
MPN: ZGC54003341562657562

Electric Water Heater 3KW Swimming Pool SPA Hot Tub Heater Thermostat New

Sign up to Newsletters. 220V 3KW Swimming Pool SPA Bath Hot Tub Electric Water Heater Thermostat. Thermostat is designed specifically for the needs of the Jacuzzi, the thermostat installed in the bottom of the tub on the massage tub, after adding hot water in the bath, start the water pump, the thermostat automatically heating insulation, the bath water temperature maintained at 30-40 adjustable, it can give your massage bathtub to create a comfortable environment. Thermostat equipped with ultra-high temperature protection thermostat switch, thermostat to limit overheating and protect users against danger, however, users should be done after the installation is complete, the first under the premise of safety checks to ensure that the operation of the thermostat’s normal function, by using the tub filled with water to a suitable level and start the system automatically checks and let the system run until the thermostat temperature stabilized at the highest level and display lights go out, use an accurate thermometer to measure the water temperature should be at 40°C. The operation of the thermostat is fully automatic. When installed properly it will turn ON after user have set the temperature by turning the controlling switch clockwise, then the heating-up indicator turns on. As long as the thermostat is on, it will heat up the water to the user-set level and maintain the temperature. User can turn the controlling switch anticlockwise to a temperature lower than the current water temperature to turn OFF the thermostat, and the heating-up indicator turns off. There is no separate heat controller for user. The 220V/3KW thermostat is designed to efficiently maintain the water temperature of a standard bathtub at the preset level of 40 (104). However, if starting with cold water, the thermostat will increase the temperature at a rate of 6 to 8 (11 to 14) per hour, depending on the initial water temperature, the room temperature, and the size of the bathtub. Once turned ON the thermostat stays ON until the temperature reaches the preset temperature, and then it will turn OFF automatically. It will stay OFF until the temperature drops a few degrees below the preset value, then it will turn back ON. The thermostat continues this ON/OFF cycle for as long as the pump is ON. The indicating lamp is located marks HEATER place. High Temperature Protection/Reset Button. In addition to the regulating thermostat, the thermostat is equipped with a manual reset High Temperature Protection to protect the user against the hazards of high temperatures. In the event of water or the thermostat enclosure reaching temperatures of higher than 49(120) because of blockage or other reasons, the High Temperature Protection will trip(interrupt power) immediately. In order to reset, let the water cool down to approximately 38 (100), then simply push the Reset Button on the top panel. The thermostat should resume operation in the normal manner. The thermostat is equipped with a pressure-sensing switch that protects the thermostat against the hazard of running the system without water. If the water level is low at the beginning or drops low during the operation water pressure is lower than 20KPa (about 2000mmHO2) the pressure sensing switch will interrupt power. Heater can only come ON when the water is at the appropriate level (water pressure is above 20KPa) and the water pump is running. Under no circumstances should any of the outlet (side) ports be closed. Water must flow through both ports when the thermostat is on. At the same time, inlet of heater must be installed perfectly matching to the outlet of water pump to give maximum water flow. Try to ensure that a minimum length of piping is maintained between the thermostat and any opening to the tub. Take off the joint on the outlet/inlet of the thermostat. Glue one side of the joint to the pipe tightly first, then hand tighten the other side to the outlet/inlet of the thermostat. After the installation of the water pump, heater and fitting system, a complete draining must take place, no water is allowed. When using electrical products basic precautions should always be followed, including the following. All electrical connections must be performed by a qualified electrician in compliance with all applicable national and local codes. Danger risk of electric shock connect only to a circuit protected by a Ground-Fault Circuit-Interrupter (GFCI). To prevent the risk of electrocution, check heater for proper ground connection. The thermostat must be properly grounded with a conductor equal to or greater than the power supply conductors. Before making any electrical connection or during installation and service make certain that the electrical power is turned off at the source or circuit breaker and take measures that it CANNOT accidentally be turned on again. Provides the suitable power line according to the thermostat. Connect the provided 220V, 3 wires with grounding branch circuit to a suitable junction box near the thermostat. The power supply should be 220V/50Hz. The blue wire should be connected to L terminal, orange wire should be connected to N terminal and the yellow and green wire should be connected to the ground terminal. Do not allow any electrical appliances (such as lights, telephone, hair dryer, radio or television) in the bathtub, 1.5 meters (5 feet) or less. The thermostat should not be used in salt water, acidic water or alkaline water, can not be used in other places chemically corrosive gases or solvents. Thermostat outlet to the bath tub in the middle of the pipe or valve or check valve can not be installed. This pool thermostat heater should be used with a circulating water pump of 500W or more to work normally. The product is easy to operate, provides a mechanical thermostat switch, you can set the temperature of temperature technology. When the product is safe and reliable movement with the flow switch, over-temperature protection switch. All using mechanical control devices durable economy. Heating thermostat liner material is 316 # stainless steel pipe and electric resistance, corrosion resistance (chlorine corrosion), and durable. The thermostat good interior circulation, not dross, easy removal. The product is small, easy to install in the bathtub at the bottom of the circulating massage pipe. Pipe Dimeter: 1/2.54cm. Size: 340 122 125mm/13.44.85inch. Net Weight: 2kg/4.4lbs. Phase Parameters: Single Phase. Suitable For: Max 2CBM Hot Tub & Swimming Pool Equipment. We believe that it is our vision and mission to provide innovative products with best service and competitive price to satisfy you. Our goal is to make sure that you can find exactly what you are looking for and make it easy for you to place your orders. California Warehouse: City of Industry, CA. If you need to return, please check twice to confirm the item not work and contact our customer service representative, let us know the detailed problem and send us some pictures for confirmation. Please make sure that item has NO man-made sabotage. Used items will not be accepted for return. All emails will be responded to within. Special circumstances will be listed clearly in the listing. Please do check everything carefully after you received the parcel, any the damage except DOA (Dead-On-Arrival) would not be covered if it’s your fault. A: The item ships from Rancho Cucamonga, CA, United States. A: Please log on your account. Q: How do I return an item? Please contact our customer service before you return an item. The item “Electric Water Heater 3KW Swimming Pool SPA Hot Tub Heater Thermostat New” is in sale since Wednesday, April 22, 2020. This item is in the category “Home & Garden\Yard, Garden & Outdoor Living\Pools & Spas\Pool Equipment & Parts\Pool Heaters & Solar Panels”. The seller is “technology-etrade” and is located in Rowland Heights, California. This item can be shipped to United States, Canada, Mexico.

Type: Pool Heater
Shape: Pro Shape
Brand: Vevor Wellplatten
MPN: LPWFR007
Model: B-M3-50MM
Country/Region of Manufacture: China
Capacity: No more than 2CBM
Material: Metal
Voltage: 220-240V/50-60Hz
Power: 3KW
Current: 14A
Wire: 3*4 Square millimeter
Pipe Dimeter: 2.54cm/1inch
Size: 340 * 122 * 125mm/13.4*4.8*5inch
Net Weight: 2kg/4.4lbs
Phase Parameters: Single Phase
Suitable For: Hot Tub & Swimming Pool Equipment
Package: 1 x Water Heating Thermostat,2 x Interface,1 x Manual
Color: As picture shows
Interface size: 50mm/1.97inch

Pool Heaters

Just another WordPress weblog

3KW 220V Swimming Pool Thermostat & SPA Heater Electric Water Heater Equipment

Fibropool FH 220 Swimming Pool Heater Heat Pump Refurbished scratch and dent

Hayward W3H250FDN Universal H-Series 250,000 BTU Pool and Spa Heater Natural Gas

Swimming Pool Electric SPA Heater Heating Thermostat 3KW Fix Temperature 220V

GAME 4721 SolarPRO Curve Solar Pool Heater for Above-Ground and Inground Pools

220V 2KW Electric Water Heater Thermostat Swimming Pool and SPA Heating Heater

Electric Water Heater Thermostat 3KW Swimming Pool & Bath SPA Hot Tub 50/60Hz

Brand new Pentair Mastertemp 250k 460732 Pool Spa Heater

Swimming Pool & Bath Tub Water Heater Pressure-Sensing Jacuzzi Easy Install

Electric Water Heater 3KW Swimming Pool SPA Hot Tub Heater Thermostat New

Tags

Recent Search Terms

Categories

Archives

Blogroll