Product description:? The swimming pool heat exchanger is made of high-grade anti-corrosion stainless steel, which has the characteristics of anti-rust and salt water resistance, so it is very durable and very suitable for chlorine or salt water swimming pools and spas. 1 1/2″ FPT is used for one side of the swimming pool water and 1″ FPT is used for hot water. The salt pond heat exchanger adopts an innovative in-line design to ensure a continuous constant temperature and indirectly transfer heat between any hot water circuit, steam circuit and any swimming pool or spa facility. The shell-and-tube heat exchanger is based on the 60°C (140°F) temperature difference between the incoming water and the hot water, and can provide a fresh pond at a rate of 135 kBtu/hr. 135 kBtu/hour Stainless Steel Tube and Shell Heat Exchanger For Pools/Spas NEW. The swimming pool heat exchanger is made of high-grade anti-corrosion stainless steel, which has the characteristics of anti-rust and salt water resistance, so it is very durable and very suitable for chlorine or salt water swimming pools and spas. It gets hot immediately without waiting. This kind of heat exchanger is a very safe, reliable, efficient and cost-effective way to heat swimming pools or spas through any hydraulic system. The heat recovery pool heater is very suitable for swimming pools, spas, hot tubs, solar, hydraulic heating, oil cooling, heat recovery, snow melting, etc. Material: 304 stainless steel. Heat transfer area: 3.2 square feet. Hot water flow rate: 25 L/min. Cold water flow: 200 L/min. Side of hot water pipe: 1 FPT. Same side port: 1 1/2 FPT. Packing size: 40 x 19 x 19cm. 1X stainless steel heat exchanger. Feedback is very important to us. It is impossible to address issues if we do not know about them! Faction is our ultimate goal. We work hard to earn your trust and future business. A If you receive a defective item, you may return it or ask for a discount. Due to time zones, our reply to your questions may not be immediately. If it’s non-workdays, please kindly be patient and wait till Monday.
1,200,000 BTU Titanium Tube and Shell. GPM Boiler Side – 30.19. GPM Pool Side – 224.06. Boiler Ports – 2 NPT. Pool Ports – 2 1/2 NPT. Port to Port – 35 13/16. Diameter – 5 1/8. Length – 34 13/16. Number of Tubes – 84. PSI Drop Hot – 2.21. PSI Drop Cold – 4.05. Working Pressure – 80 PSI. BTU rated with 180F Boiler and 80F Pool. This unit is suitable for pools/spas that are 103,200 gallons. These heat exchangers are constructed with a Titanium shell and Titanium corrugated inner tubes to ensure high velocities inside the unit. This is a very reliable, efficient and cost effective way to transfer heat indirectly between any boiler circuit and any pool or spa circuit. The units are designed for both horizontal and vertical mounting. Port sizes: (to/from Boiler) 2″ – (to/from Pool) 2 1/2″. It is recommended to always install the unit with the mounting bracket (mounting brackets included with each unit) fixed to a wall, and/or ceiling or floor to prevent water hammer or vibrations which could damage the unit. Always install the Titanium Pool & Spa Heat Exchanger in a counter flow pattern. The units should be installed downstream of the filtration and pumping equipment. The boiler water must be assisted and the usual precautions taken to prevent air locks. The pool water pump should be controlled by a thermostat in the pool pipe work before the heat exchanger and set at the required temperature. Titanium Pool and Spa Heat Exchangers are suited for a large range of chemical environments and conditions, due to a thin, invisible, but extremely protective surface oxide film (primarily TiO2). Titanium is especially known for its elevated resistance to localized attack and stress corrosion in aqueous chlorides e. Brines, seawater and other halides and wet halogens e. Wet CI2 or CI2 salt, brines, and to hot, highly oxidizing, acidic solutions e. FeCI3 and nitric acid solutions. Titanium is also recognized for its superior resistance to erosion, erosion-corrosion, cavitation’s and impingement in flowing, turbulent fluids. For occasional (holidays & weekends) use pools we recommend a 2x output multiplier to obtain a 2°F/hr heat up rate; 2. Nominal values are based on 60°C temperature between incoming heating and heated water. Swimming pools, spas heating – Hot tube heating – Floor heating – Driveway snowmelts. Oil cooling or heating – Steam condenser – District heating – Transmission and engine cooler – Boiler sample cooler – Waste water heat recovery – Industry process applications. It is the purchaser’s responsibility to ensure that all fluids in contact with the products are compatible with the construction material of the product, this includes operational fluids and cleaning fluids. Corrosive environments are often a combination of chemical levels, flow rates and temperatures. Failure to ensure this will result in damages to the product.
360,000 BTU Stainless Steel Tube and Shell. Swimming pools, spas heating. BTU rated with 180F Boiler and 80F Pool This unit is suitable for pools/spas that are30,960 gallons. Port to Port – 27 13/16.
360,000 BTU Titanium Tube and Shell. Swimming pools, spas heating. BTU rated with 180F Boiler and 80F Pool. Port to Port – 27 13/16. Hot tube heating. Nominal values are based on 60°C temperature between incoming heating and heated water.
Product description:? The swimming pool heat exchanger is made of high-grade anti-corrosion stainless steel, which has the characteristics of anti-rust and salt water resistance, so it is very durable and very suitable for chlorine or salt water swimming pools and spas. 1 1/2″ FPT is used for one side of the swimming pool water and 1″ FPT is used for hot water. The salt pond heat exchanger adopts an innovative in-line design to ensure a continuous constant temperature and indirectly transfer heat between any hot water circuit, steam circuit and any swimming pool or spa facility. The shell-and-tube heat exchanger is based on the 60°C (140°F) temperature difference between the incoming water and the hot water, and can provide a fresh pond at a rate of 135 kBtu/hr.
6,000,000 BTU Stainless Steel Tube and Shell. Boiler Ports – 2 1/2 NPT. Pool Ports – 4 NPT. Diameter – 8.62. Working Pressure – 80 PSI. BTU rated with 180F Boiler and 80F Pool. This unit is suitable for pools/spas that are 430,000 gallons. These heat exchangers are constructed with a stainless steel 316L shell and stainless steel 316L corrugated inner tubes to ensure high velocities inside the unit. This is a very reliable, efficient and cost effective way to transfer heat indirectly between any boiler circuit and any pool or spa circuit. The units are designed for both horizontal and vertical mounting. Port sizes: (to/from Boiler) 2 1/2″ – (to/from Pool) 4″. It is recommended to always install the unit with the mounting bracket (mounting brackets included with each unit) fixed to a wall, and/or ceiling or floor to prevent water hammer or vibrations which could damage the unit. Always install the Stainless Steel Pool & Spa Heat Exchanger in a counter flow pattern. The units should be installed downstream of the filtration and pumping equipment. The boiler water must be assisted and the usual precautions taken to prevent air locks. The pool water pump should be controlled by a thermostat in the pool pipe work before the heat exchanger and set at the required temperature. Stainless Steel Pool and Spa Heat Exchangers are not suited for saline or salt water environments. For those applications please use one of our Titanium units. For occasional (holidays & weekends) use pools we recommend a 2x output multiplier to obtain a 2°F/hr heat up rate. Nominal values are based on 60°C temperature between incoming heating and heated water. Swimming pools, spas heating – Hot tube heating – Floor heating – Driveway snowmelts. Oil cooling or heating – Steam condenser – District heating – Transmission and engine cooler – Boiler sample cooler – Waste water heat recovery – Industry process applications. The following fluids are prohibited for use as a flushing agent for stainless steel pool and spa heat exchangers. Hydrochloric Acid up to 0.1% concentration. Solutions the contain MCI. Chlorides (MgCI2, NaCI between 0.01 – 1%, CuCI up to 1%, CaCI2 from 5% to saturation). Any fluid that will deposit alkaline residue or phosphorous. It is the purchaser’s responsibility to ensure that all fluids in contact with the products are compatible with the construction material of the product, this includes operational fluids and cleaning fluids. Corrosive environments are often a combination of chemical levels, flow rates and temperatures. Failure to ensure this will result in damages to the product.
55,000 BTU Stainless Steel Tube and Shell. GPM Boiler Side – 7.49. GPM Pool Side – 48.84. Boiler Ports – 3/4 NPT. Pool Ports – 1 NPT. Port to Port – 7 1/2. Diameter – 2 1/2. Length – 13 1/4. Number of Tubes – 19. PSI Drop Hot. PSI Drop Cold – 1.03. Working Pressure – 80 PSI. BTU rated with 180F Boiler and 80F Pool. This unit is suitable for pools/spas that are 4,730 gallons. These heat exchangers are constructed with a stainless steel 316L shell and stainless steel 316L corrugated inner tubes to ensure high velocities inside the unit. This is a very reliable, efficient and cost effective way to transfer heat indirectly between any boiler circuit and any pool or spa circuit. The units are designed for both horizontal and vertical mounting. Port sizes: (to/from Boiler) 3/4″- (to/from Pool) 1 “. It is recommended to always install the unit with the mounting bracket (mounting brackets included with each unit) fixed to a wall, and/or ceiling or floor to prevent water hammer or vibrations which could damage the unit. Always install the Stainless Steel Pool & Spa Heat Exchanger in a counter flow pattern. The units should be installed downstream of the filtration and pumping equipment. The boiler water must be assisted and the usual precautions taken to prevent air locks. The pool water pump should be controlled by a thermostat in the pool pipe work before the heat exchanger and set at the required temperature. Stainless Steel Pool and Spa Heat Exchangers are not suited for saline or salt water environments. For those applications please use one of our Titanium units. For occasional (holidays & weekends) use pools we recommend a 2x output multiplier to obtain a 2°F/hr heat up rate; 2. Nominal values are based on 60°C temperature between incoming heating and heated water. Swimming pools, spas heating – Hot tube heating – Floor heating – Driveway snowmelts. Oil cooling or heating – Steam condenser – District heating – Transmission and engine cooler – Boiler sample cooler – Waste water heat recovery – Industry process applications. The following fluids are prohibited for use as a flushing agent for stainless steel pool and spa heat exchangers. Hydrochloric Acid up to 0.1% concentration. Solutions the contain MCI. Chlorides (MgCI2, NaCI between 0.01 – 1%, CuCI up to 1%, CaCI2 from 5% to saturation). Any fluid that will deposit alkaline residue or phosphorous. It is the purchaser’s responsibility to ensure that all fluids in contact with the products are compatible with the construction material of the product, this includes operational fluids and cleaning fluids. Corrosive environments are often a combination of chemical levels, flow rates and temperatures. Failure to ensure this will result in damages to the product.
55,000 BTU Stainless Steel Tube and Shell. GPM Boiler Side – 7.49. GPM Pool Side – 48.84. Boiler Ports – 3/4 NPT. Pool Ports – 1 NPT. Port to Port -7 1/2. Diameter – 2 1/2. Length – 13 1/4. Number of Tubes – 19. PSI Drop Hot. PSI Drop Cold – 1.03. Working Pressure – 80 PSI. BTU rated with 180F Boiler and 80F Pool. This unit is suitable for pools/spas that are 4,730 gallons. These heat exchangers are constructed with a stainless steel 316L shell and stainless steel 316L corrugated inner tubes to ensure high velocities inside the unit. This is a very reliable, efficient and cost effective way to transfer heat indirectly between any boiler circuit and any pool or spa circuit. The units are designed for both horizontal and vertical mounting. Port sizes: (to/from Boiler) 3/4″ – (to/from Pool) 1″. Ited for saline or salt water environments. For those applications please use one of our Titanium units. For occasional (holidays & weekends) use pools we recommend a 2x output multiplier to obtain a 2°F/hr heat up rate. Nominal values are based on 60°C temperature between incoming heating and heated water. Swimming pools, spas heating – Hot tube heating – Floor heating – Driveway snowmelts. Oil cooling or heating – Steam condenser – District heating – Transmission and engine cooler – Boiler sample cooler – Waste water heat recovery – Industry process applications. The following fluids are prohibited for use as a flushing agent for stainless steel pool and spa heat exchangers. Hydrochloric Acid up to 0.1% concentration. Solutions the contain MCI. Chlorides (MgCI2, NaCI between 0.01 – 1%, CuCI up to 1%, CaCI2 from 5% to saturation). Any fluid that will deposit alkaline residue or phosphorous. It is the purchaser’s responsibility to ensure that all fluids in contact with the products are compatible with the construction material of the product, this includes operational fluids and cleaning fluids. Corrosive environments are often a combination of chemical levels, flow rates and temperatures. Failure to ensure this will result in damages to the product. This item is in the category “Home & Garden\Yard, Garden & Outdoor Living\Pools & Spas\Pool Equipment & Parts\Pool Heaters & Solar Panels”. The seller is “badger-pipe” and is located in this country: US. This item can be shipped worldwide.
- Brand: Undisclosed
- Type: Heat Pump
- UPC: 689807256751
600,000 BTU Stainless Steel Tube and Shell. GPM Boiler Side – 17.44. GPM Pool Side – 114.16. Boiler Ports – 2 NPT. Pool Ports – 21/2 NPT. Port to Port – 25 3/8. Diameter – 4.38. Length – 33 1/2. Number of Tubes – 42. PSI Drop Hot – 1.22. PSI Drop Cold – 3.07. Working Pressure – 80 PSI. BTU rated with 180F Boiler and 80F Pool. This unit is suitable for pools/spas that are 51,600 gallons. These heat exchangers are constructed with a stainless steel 316L shell and stainless steel 316L corrugated inner tubes to ensure high velocities inside the unit. This is a very reliable, efficient and cost effective way to transfer heat indirectly between any boiler circuit and any pool or spa circuit. The units are designed for both horizontal and vertical mounting. Port sizes: (to/from Boiler) 2″ – (to/from Pool) 2 1/2″. It is recommended to always install the unit with the mounting bracket (mounting brackets included with each unit) fixed to a wall, and/or ceiling or floor to prevent water hammer or vibrations which could damage the unit. Always install the Stainless Steel Pool & Spa Heat Exchanger in a counter flow pattern. The units should be installed downstream of the filtration and pumping equipment. The boiler water must be assisted and the usual precautions taken to prevent air locks. The pool water pump should be controlled by a thermostat in the pool pipe work before the heat exchanger and set at the required temperature. Stainless Steel Pool and Spa Heat Exchangers are not suited for saline or salt water environments. For those applications please use one of our Titanium units. For occasional (holidays & weekends) use pools we recommend a 2x output multiplier to obtain a 2°F/hr heat up rate. Nominal values are based on 60°C temperature between incoming heating and heated water. Swimming pools, spas heating – Hot tube heating – Floor heating – Driveway snowmelts. Oil cooling or heating – Steam condenser – District heating – Transmission and engine cooler – Boiler sample cooler – Waste water heat recovery – Industry process applications. The following fluids are prohibited for use as a flushing agent for stainless steel pool and spa heat exchangers. Hydrochloric Acid up to 0.1% concentration. Solutions the contain MCI. Chlorides (MgCI2, NaCI between 0.01 – 1%, CuCI up to 1%, CaCI2 from 5% to saturation). Any fluid that will deposit alkaline residue or phosphorous. It is the purchaser’s responsibility to ensure that all fluids in contact with the products are compatible with the construction material of the product, this includes operational fluids and cleaning fluids. Corrosive environments are often a combination of chemical levels, flow rates and temperatures. Failure to ensure this will result in damages to the product. This item is in the category “Home & Garden\Yard, Garden & Outdoor Living\Pools & Spas\Pool Equipment & Parts\Pool Heaters & Solar Panels”. The seller is “badger-pipe” and is located in this country: US. This item can be shipped worldwide.
- Brand: Unbranded
- Type: heat exchanger
- UPC: 689807256799
155,000 BTU Stainless Steel Tube and Shell. GPM Boiler Side – 8.46. GPM Pool Side – 62.66. Boiler Ports – 1 NPT. Pool Ports – 1 1/2 NPT. Port to Port – 9 1/8. Diameter – 3 3/16. Length – 15 3/4. Number of Tubes – 30. PSI Drop Hot – 1.10. PSI Drop Cold – 1.58. Working Pressure – 80 PSI. BTU rated with 180F Boiler and 80F Pool. This unit is suitable for pools/spas that are 13,330 gallons. These heat exchangers are constructed with a stainless steel 316L shell and stainless steel 316L corrugated inner tubes to ensure high velocities inside the unit. This is a very reliable, efficient and cost effective way to transfer heat indirectly between any boiler circuit and any pool or spa circuit. The units are designed for both horizontal and vertical mounting. Port sizes: (to/from Boiler) 1″ – (to/from Pool) 1 1/2″. It is recommended to always install the unit with the mounting bracket (mounting brackets included with each unit) fixed to a wall, and/or ceiling or floor to prevent water hammer or vibrations which could damage the unit. Always install the Stainless Steel Pool & Spa Heat Exchanger in a counter flow pattern. The units should be installed downstream of the filtration and pumping equipment. The boiler water must be assisted and the usual precautions taken to prevent air locks. The pool water pump should be controlled by a thermostat in the pool pipe work before the heat exchanger and set at the required temperature. Stainless Steel Pool and Spa Heat Exchangers are not suited for saline or salt water environments. For those applications please use one of our Titanium units. For occasional (holidays & weekends) use pools we recommend a 2x output multiplier to obtain a 2°F/hr heat up rate; 2. Nominal values are based on 60°C temperature between incoming heating and heated water. Swimming pools, spas heating – Hot tube heating – Floor heating – Driveway snowmelts. Oil cooling or heating – Steam condenser – District heating – Transmission and engine cooler – Boiler sample cooler – Waste water heat recovery – Industry process applications. The following fluids are prohibited for use as a flushing agent for stainless steel pool and spa heat exchangers. Hydrochloric Acid up to 0.1% concentration. Solutions the contain MCI. Chlorides (MgCI2, NaCI between 0.01 – 1%, CuCI up to 1%, CaCI2 from 5% to saturation). Any fluid that will deposit alkaline residue or phosphorous. It is the purchaser’s responsibility to ensure that all fluids in contact with the products are compatible with the construction material of the product, this includes operational fluids and cleaning fluids. Corrosive environments are often a combination of chemical levels, flow rates and temperatures. Failure to ensure this will result in damages to the product. This item is in the category “Home & Garden\Yard, Garden & Outdoor Living\Pools & Spas\Pool Equipment & Parts\Pool Heaters & Solar Panels”. The seller is “badger-pipe” and is located in this country: US. This item can be shipped worldwide.
- Brand: Undisclosed
- Type: Heat Pump
- UPC: 689807256584
