Stationary solar panel kit is an eco-friendly power source designed for boat, home off-grid charging, camping and outdoor activities. Made from Class A monocrystalline cells, it absorbs sunlight efficiently, turning it into your portable power source. You can use this kit as well as other battery types to charge 12V deep cycle batteries. If you need a solar panel with a different wattage or maximum power, check out the other solar panel products in our store now. Uses an anti-reflective, low iron-tempered glass on top, with high transparency of up to 91.5%. Compared with conventional solar panels, it allows more direct sunlight to be converted to electrical power. Reliable & D urable. This solar panel is made of advanced encapsulation material with multi-layered sheet laminations to protect cells from physical damage or distortion, improving cell performance and providing lasting solar panel durability. Corrosion-resistant aluminum frame design with sturdy corner supports ensures that it endures the outdoors for an extended period of time without damage or loss of performance. No need to worry about bad weather. These IP67 waterproof solar connectors ensure that the water and dust will not enter the connector during extended outdoor use. Effectively preventing water from seeping in. Perfect for your yacht and marine applica. Maximum Power Current(IMP): 11.12A. Maximum Power Voltage(VMP): 18.0V. Short Circuit Current(ISC): 12.22A. Solar Cell: Monocrystalline Grade A+. Open Circuit Voltage(VOC) :21.6V. SIZE:50.7829.921.18in. 1: Does a Solar Panel produce full power? A: In most cases, it is normal for a solar panel to not be able to provide its full nominal power. Factors affecting the performance of solar panels. Peak Sun Hours, Sunlight Angle, Operating Temperature, Installation Angle, Panel Shading, Adjacent Buildings Etc.. 2: How to test a solar panel? A: The ideal conditions: Test in the noon, under a clear sky, panels should be at 25 degrees tilted towards the sun, and the battery is at a low state/less than 40% SOC. Disconnect the solar panel from any other loads, using a multimeter to test the panel’s current and voltage. 3: How does temperature affect solar panel efficiency? A: Solar panels are generally tested at about 77°F/25°C and are rated to perform at peak efficiency between 59°F/15°C and 95°F/35°C. Temperature going up or down will change the efficiency of the panels. For example, if the temperature coefficient of power is -0.5%, then the panel maximum power will be reduced by 0.5% for every 50°F/10°C rise. 5: Can I connect different solar panels together? A: Though mixing different solar panels is not recommended, the mismatch can be achievable as long as each panel’s electrical parameters (voltage, current, wattage) are carefully considered.
Pool Chemicals & Testing. Spa Chemicals & Sanitizers. Sign up to receive special insider notifications of deals, promotions, and new items! OEM Hayward H-Series Pool Heater Replacement Display Board Only IDXL2DB1930. Hayward H-Series Heater Replacement Display Board Only. Fits Hayward H-Series Low Nox Induced Draft Heaters. Genuine Hayward Replacement Part. Questions about this item? To make sure we get the order to you as fast as possible, orders are processed as soon as they come in. We cannot guarantee that any order can be cancelled once placed and processed. Included in this but not limited to are Heat Pumps, Gas Heaters, Large Filters, Slides, and Diving Boards. These products are delivered to the front of the driveway, not to the garage or installation site. The trucking company is not responsible to transport your items anywhere other than the front of your driveway. In this circumstance, we will call you with the additional charges. To help make this process as smooth as possible please follow these guidelines. Sign Bill of Lading (receiving bill). This document says that the order has been received. This all states that the order has arrived in good condition. It is the customer’s responsibility to inspect all packages received. This document also states the number of cartons you are receiving, please make sure this number is the same as the actual number of cartons received. It is your responsibility to make sure your order is in good condition upon receipt. Backyard Pool Superstore is here for all of your pool and backyard needs. Here at Backyard Pool Superstore, we understand that mistakes can be made. The packaging must be resealed with. See below for more details. When you sign for the product, you state the product arrived in good condition, and you accept the condition it was delivered in. Our staff is dedicated to making sure your experience with us is not only good, but the best! We are not just “Internet retailers”, we are pool and backyard professionals that have been in business for over 20 years. We pride ourselves on fast, professional customer service. We use the latest technology to assist you with your pool, spa, patio, and backyard needs. The Best Customer Service and Expert Advice. With many years of experience in all aspects of the pool and backyard industry, we are here to help you with all of your questions. If one of our staff members cannot help you immediately, we will not rest until we find an answer to your question.
What’s Included: 1 X Stainless Steel Heat Exchanger 2 X Fixed Bracket Weights&Dimensions Packing Size: 48.514cm/19.095.5inch Weight: 5.2kg Specifications : Material: 304 Stainless Steel Output: 200 Kbtu/Hour Heat Transfer Area: 4.8 Square Feet Hot Water Flow Rate: 30 L/Min Cold Water Flow: 250 L/Min Side of Hot Water Pipe: 1″ Fpt Same Side Port: 1 1/2″ Fpt. Welcome to Our Store. The Swimming Pool Heat Exchanger Is Made of. High-grade Anticorrosive Stainless Steel. Which Has the Characteristics of Anti-rust and Salt Water Resistance, so It Is Very Durable and Very Suitable for Chlorine or Salt Water Swimming Pools and Spas. 1 1/2″ Fpt Is Used on One Side of the Swimming Pool Water, and 1″ Fpt Is Used for Hot Water. The Salt Pond Heat Exchanger Adopts an. To Ensure a Continuous Constant Temperature and Indirectly Transfer Heat Between Any Hot Water Circuit, Steam Circuit and Any Swimming Pool or Spa Facility. Hell-and-tube Heat Exchanger Is Based on the 60°C (140°F) Temperature Difference Between the Inlet and Hot Water. And Can Provide a Fresh Pond of 200 Kbtu/Hr. It Gets Hot Immediately Without Waiting. This Kind of Heat Exchanger Is a Very Safe, Reliable, Efficient and Cost-effective Way to Heat Swimming Pools or Spas Through Any Hydraulic System. The Heat Recovery Pool Heater Is Very Suitable for. Swimming Pools, Spas, Hot Tubs, Solar, Hydraulic Heating, Oil Cooling, Heat Recovery, Snow Melting. 1 X Stainless Steel Heat Exchanger. 2 X Fixed Bracket. Packing Size: 48.514cm/19.095.5inch. Material: 304 Stainless Steel. Heat Transfer Area: 4.8 Square Feet. Hot Water Flow Rate. Side of Hot Water Pipe: 1 Fpt. Feedback is very important to us. It is impossible to address issues if we do not know about them! Faction is our ultimate goal. We work hard to earn your trust and future business. A If you receive a defective item, you may return it or ask for a discount. Due to time zones, our reply to your questions may not be immediately. If it’s non-workdays, please kindly be patient and wait till Monday.
What’s Included: 1 X Stainless Steel Heat Exchanger 2 X Fixed Bracket Weights&Dimensions Packing Size: 48.514cm/19.095.5inch Weight: 5.2kg Specifications : Material: 304 Stainless Steel Output: 200 Kbtu/Hour Heat Transfer Area: 4.8 Square Feet Hot Water Flow Rate: 30 L/Min Cold Water Flow: 250 L/Min Side of Hot Water Pipe: 1″ Fpt Same Side Port: 1 1/2″ Fpt. New Swimming Pool Heat Exchanger 200 kBtu/hour 1″+1 1/2″ FPT Stainless Steel. The Swimming Pool Heat Exchanger Is Made of. High-grade Anticorrosive Stainless Steel. Which Has the Characteristics of Anti-rust and Salt Water Resistance, so It Is Very Durable and Very Suitable for Chlorine or Salt Water Swimming Pools and Spas. 1 1/2″ Fpt Is Used on One Side of the Swimming Pool Water, and 1″ Fpt Is Used for Hot Water. The Salt Pond Heat Exchanger Adopts an. To Ensure a Continuous Constant Temperature and Indirectly Transfer Heat Between Any Hot Water Circuit, Steam Circuit and Any Swimming Pool or Spa Facility. Hell-and-tube Heat Exchanger Is Based on the 60°C (140°F) Temperature Difference Between the Inlet and Hot Water. And Can Provide a Fresh Pond of 200 Kbtu/Hr. It Gets Hot Immediately Without Waiting. This Kind of Heat Exchanger Is a Very Safe, Reliable, Efficient and Cost-effective Way to Heat Swimming Pools or Spas Through Any Hydraulic System. The Heat Recovery Pool Heater Is Very Suitable for. Swimming Pools, Spas, Hot Tubs, Solar, Hydraulic Heating, Oil Cooling, Heat Recovery, Snow Melting. 1 X Stainless Steel Heat Exchanger. 2 X Fixed Bracket. Packing Size: 48.514cm/19.095.5inch. Material: 304 Stainless Steel. Heat Transfer Area: 4.8 Square Feet. Hot Water Flow Rate. Side of Hot Water Pipe: 1 Fpt. Feedback is very important to us. It is impossible to address issues if we do not know about them! Faction is our ultimate goal. We work hard to earn your trust and future business. A If you receive a defective item, you may return it or ask for a discount. Due to time zones, our reply to your questions may not be immediately. If it’s non-workdays, please kindly be patient and wait till Monday.
Wide Application? This heater is specifically designed for Value Series and M7 Series Spa, which is a perfect replacement for Balboa part # 58083. Important Specification? Heater Length: 15″, Heater Diameter: 2″. 5.5KW, 220V heater element. Please choose correct rated heater for replacement and put it in right position to extend the service life of the device. This heater is specifically designed for Value Series and M7 Series Spa, which is a perfect replacement for Balboa part # 58083. What You Get? Package includes 1 heater, 1 pair of 2. 0 heater split nuts, 1 pair of 2. 0 heater tailpieces with o-ring gaskets. Superior Construction? The heater housing is made of premium stainless steel to prevent corrosion and rust, sturdy and wear resistant for providing excellent performance and lasting service time. Single item or set. If you need return, please contact our customer service representative, let us know the detailed problem and send us some pictures for confirmation. Thank you for your understanding. For John Deere Tractor AM131898 AM132036 AM130685 Universal Cup Beverage Holder. 190595GS Pressure Washer Seal Kit For Briggs & Stratton Pumps 580752550. K-0650 Compression Ring Kit DAC-308 for Craftsman DeVilbiss Porter Cable 165080. 14 Bandsaw Trunnions with Degree Scale for Most 14-Inch Wood Band Saws 2Pcs. Third Function Valve Kit for Kubota MX4700, MX4800, MX5100, MX5200, MX5800. AM129514 Front Left and Right Shocks Absorber for John Deere Gator TE TH TS TX. Hydraulic Cylinder Welded Double Acting 4.5″ Bore 24″ For Log Splitter 3500PSI. SX244DA Lateral Assembly + Center Pipe for Hayward Sand Filter Pro Series S270T2. For John Deere M136635 Arm 320 335 345 GT262 GX325 GX345 LX176 LX188 S2348 S2554.
Pool Heat Exchanger Tube 200K Same Side 1″+ 1 1/2″FPT Stainless 200k Btu/hour. The swimming pool heat exchanger is made of high-grade anticorrosive stainless steel, which has the characteristics of anti-rust and salt water resistance, so it is very durable and very suitable for chlorine or salt water swimming pools and spas. 1 1/2″ FPT is used on one side of the swimming pool water, and 1″ FPT is used for hot water. The salt pond heat exchanger adopts an innovative in-line design to ensure a continuous constant temperature and indirectly transfer heat between any hot water circuit, steam circuit and any swimming pool or spa facility. The shell-and-tube heat exchanger is based on the 60°C (140°F) temperature difference between the inlet and hot water, and can provide a fresh pond of 200 kBtu/hr. It gets hot immediately without waiting. This kind of heat exchanger is a very safe, reliable, efficient and cost-effective way to heat swimming pools or spas through any hydraulic system. The heat recovery pool heater is very suitable for swimming pools, spas, hot tubs, solar, hydraulic heating, oil cooling, heat recovery, snow melting, etc. Material: 304 stainless steel. Heat transfer area: 4.8 square feet. Hot water flow rate: 30 L/min. Cold water flow: 250 L/min. Side of hot water pipe: 1 FPT. Same side port: 1 1/2 FPT. Product Size: 48.514cm/19.095.5inch. 1 x stainless steel heat exchanger. 2 x fixed bracket. Feedback is very important to us. It is impossible to address issues if we do not know about them! Faction is our ultimate goal. We work hard to earn your trust and future business. A If you receive a defective item, you may return it or ask for a discount. Due to time zones, our reply to your questions may not be immediately. If it’s non-workdays, please kindly be patient and wait till Monday. Creative Design, Durable Material, Beautiful Appearance. Easy installation, Convenient Use, Easy Operation. 11.5lbs(5.2kg). Gas / Wood / Solar / Heat Pump / Electricity. Hot Water flow rate. Side of hot water pipe. 4.8 square feet.
Heater Repair Kit Compatible with Pentair Mastertemp and Starite Max-E-Therm Heater – Value Bundle Includes – Most Sensors, Orings and Pads Included (Value Bundle). Value Bundle – The perfect Pentair Mastertemp parts list designed to fix most problems within the Pentair Pool Heater. This Pentair Mastertemp 400 parts bundle is designed for the pool professional or the homeowner. Compatibility: This pressure switch is compatible with all BTU’s of the Pentair Mastertemp heater parts and Mastertemp 400 parts. It will also work with HD Versions of the heater as well. Affordable: Unlike the OEM, this parts list is the most affordable Master Temp 400 and Sta Rite Repair Kit on the market. Compatible with all Pentair Pool Heater parts. Kit Includes: Thermistor, Stack Flue Sensor, High Limit Switch, AGS, Igniter, Thermal Regulator Kit, Membrane Pad, Manifold Oring Set, Bypass Valve, and Air Flow Switch. The kit contains enough replacement parts to fix various different issues.
Pool/Spa Part – Raypak – Tube Bundle, Copper, R406A, R407A – 010062F. Raypak Tube Bundle Copper R406A R407A (010062F). View more great items. DiversiTech EL2436-2 E-Lite Plastic Equipment Pad 24″ X 36″ X 2. Hayward W3S210S Sand Filter 21in. Poolvergnuegen Steering Cam (896584000-310). Raypak Thermostat Control (003346F). This listing is currently undergoing maintenance, we apologise for any inconvenience caused.
Product description:? The pool heat exchanger is made of high-grade anti-corrosion stainless steel, which has the characteristics of anti-rust and salt water resistance, so it is very durable and very suitable for chlorine or salt pools and spas. 2 inch FPT is used for swimming pool water, and 1 inch FPT is used for hot water. The salt pond heat exchanger adopts an innovative in-line design to ensure a continuous constant temperature and indirectly transfer heat between any hot water circuit, steam circuit and any swimming pool or spa facility. The shell-and-tube heat exchanger is based on the 60°C (140°F) temperature difference between the inlet and hot water, and can provide a fresh pond of 400 kBtu/hr. It gets hot immediately without waiting. Tube and Shell Heat Exchanger 400kBtu 304 Stainless Steel for Spa Heat Recovery. 304 Stainless Steel Tube and Shell Heat Exchanger 400kBtu for Spa Heat Recovery. The pool heat exchanger is made of high-grade anti-corrosion stainless steel, which has the characteristics of anti-rust and salt water resistance, so it is very durable and very suitable for chlorine or salt pools and spas. This kind of heat exchanger is a very safe, reliable, efficient and cost-effective way to heat swimming pools or spas through any hydraulic system. The heat recovery pool heater is very suitable for swimming pools, spas, hot tubs, solar, hydraulic heating, oil cooling, heat recovery, snow melting, etc. Material: 304 stainless steel. Output: 400 kBtu / hr. Heat transfer area: 11.8 square feet. Hot water flow rate: 50 L/min. Cold water flow: 360 L/min. Side of hot water pipe: 1 FPT. Port on the same side: 2 inch FPT. 1 x stainless steel heat exchanger. 2 x fixed bracket. Feedback is very important to us. It is impossible to address issues if we do not know about them! Faction is our ultimate goal. We work hard to earn your trust and future business. A If you receive a defective item, you may return it or ask for a discount. Due to time zones, our reply to your questions may not be immediately. If it’s non-workdays, please kindly be patient and wait till Monday.
