Ideal for Above Ground Pools. The pool heat pump is designed for small pools with up to 2700 gallons of water. It is suitable for above-ground swimming pools, hot tubs or spas. Extend Your Swim Season. Nothing beats a warm swimming pool for your kids, pets and the whole family. What you’ll need is a highly efficient, low operating cost heating system. A pool heat pump for swimming pools will extend the fun for a few more months. The pool heater is a heat pump specifically designed for swimming pools. The operation only requires very limited electric input, thus its heat conversion rate can reach a score of COP 5.4. In other words, for every cent of electricity spent, 5.4 times heat is generated. Equipped with a powerful compressor, the pool heat pump has a capacity of 14331BTU/hr. The swimming pool heater is easy to operate, which allowing fast and easy hookup without professional installation. Just hook up several quick connectors, then plug and play. No need tools, no need plumber. High Quality and Safer. Available with the child lock and an advanced protection system which has auto electrical leakage and low-voltage switch, high and low-temperature, and compressor discharge over-high protection. The pure titanium heat exchanger can resist any corrosion from pool water. An intelligent control system maintains the pool temperature at a consistent level. Mini Swimming Pool Heat Pump is specifically designed for mini swimming pools, not an solar or gas heater. The operation only requires very limited electric input, hence its high efficiency and the heat conversion rate can reach a score of COP. The solar pool heater is too dependent on weather conditions and the amount of sunlight, hence limiting its usage. Without enough sunlight, the solar heater cannot run efficiently. In contrast, Mini Pool Heat Pump is not affected by weather conditions and can be turned on anytime as long as outdoor temp. Is above 40F, so that your pool’s temperature can be adjusted whenever you want. Equipped with a powerful compressor, the pool heat pump has 2 kinds of capacity, A80.6W80.6 14331 BTU/hr and A56 W78.8 8496 BTU/hr. It also adds 4 way valve to help defrosting automatically. A Better Way to Extend Your Swimming Season — Mini Pool Heat Pump. In order to provide better service to buyers and improve our service quality, we interviewed hundreds of buyers who have used other companies’ swimming pool heat pumps and asked what problems they encountered during the use of heat pumps. Our machine has completely ruled out these problems, please rest assured to use. These questions are also to improve your understanding of the machine. You can contact me at any time if you have any questions after receiving our machine. 2 Install: Check if there is ventilation in the installation environment, there must be enough clearance around the machine for ventilation; connect the power supply, the voltage should be 110V, and see if the fan will turn; if the fan will turn, turn it on for 45 minutes continuously; the ambient temperature is not higher than 20 degrees, it will automatically frost 3 Unable to defrost is 1 You have to turn on the machine and check the fault code to see if the machine is operating normally, and the frosting should be automatically removed after the conditions are met; 2 Check if there is ventilation in the installation environment. There must be enough clearance around the machine for ventilation; connect the power supply and see if the fan will rotate; if the fan will rotate, start it for 45 minutes continuously; automatic cream. No change in temperature. 1 It needs to be covered with a pool cover (pool cover) to keep warm 2 The power of the circulating water pump should not be higher than 600GAL/hour, 530GAL/hour is recommended, and 400GAL/hour is the best 3 The capacity of the pool is 2700GAL, preferably within 2100GAL 4 The larger the pool capacity, the lower the temperature, the lower the humidity, and the worse the heating effect 5 When encountering this situation, it is generally necessary to know the capacity of the customer’s swimming pool, outdoor temperature, humidity, and the state where the customer is located. 6 The power supply voltage should be between 110-120V. (1) E08 code The filter water pump does not circulate with the water in the pool, and the water temperature probe only detects the water temperature in the titanium heat exchanger, and the water is low and quickly protected against high temperature; Treatment: first disconnect the machine from the power supply – connect the filter water pump, confirm that the filter water pump and the pool are running with water – connect the machine to 110V power supply, start the machine. 2.1 Check the power supply, whether it is connected to 110V or 220V power supply according to the requirements of the machine; 2.2 The power and flow of the circulating water pump should be used in accordance with the requirements of the machine nameplate and instructions; 2.3 There must be enough places around the place where the machine is installed to dissipate heat, and it cannot be blocked. If the machine is not heated, first check the fault code or panel display on the control panel; 2.4 If the machine is found to be frosted, check the air humidity and ambient temperature. The defrosting condition of the machine is that the machine should be powered on continuously for 45 minutes, the ambient temperature is within 20 degrees, and the air humidity is within 70%.
