5,000,000 BTU Stainless Steel Tube and Shell. GPM Boiler Side 150.00. GPM Pool Side 934.00. Boiler Ports 2 1/2 NPT. Pool Ports 4 NPT. Number of Tubes – 292. PSI Drop Hot 11.67. PSI Drop Cold 12.96. Working Pressure – 80 PSI. BTU rated with 180F Boiler and 80F Pool. This unit is suitable for pools/spas that are 430,000 gallons. These heat exchangers are constructed with a stainless steel 316L shell and stainless steel 316L corrugated inner tubes to ensure high velocities inside the unit. This is a very reliable, efficient and cost effective way to transfer heat indirectly between any boiler circuit and any pool or spa circuit. The units are designed for both horizontal and vertical mounting. Port sizes: (to/from Boiler) 2 1/2″ – (to/from Pool) 4″. It is recommended to always install the unit with the mounting bracket (mounting brackets included with each unit) fixed to a wall, and/or ceiling or floor to prevent water hammer or vibrations which could damage the unit. Always install the Stainless Steel Pool & Spa Heat Exchanger in a counter flow pattern. The units should be installed downstream of the filtration and pumping equipment. The boiler water must be assisted and the usual precautions taken to prevent air locks. The pool water pump should be controlled by a thermostat in the pool pipe work before the heat exchanger and set at the required temperature. Stainless Steel Pool and Spa Heat Exchangers are not suited for saline or salt water environments. For those applications please use one of our Titanium units. For occasional (holidays & weekends) use pools we recommend a 2x output multiplier to obtain a 2°F/hr heat up rate. Nominal values are based on 60°C temperature between incoming heating and heated water. Swimming pools, spas heating – Hot tube heating – Floor heating – Driveway snowmelts. Oil cooling or heating – Steam condenser – District heating – Transmission and engine cooler – Boiler sample cooler – Waste water heat recovery – Industry process applications. The following fluids are prohibited for use as a flushing agent for stainless steel pool and spa heat exchangers. Hydrochloric Acid up to 0.1% concentration. Solutions the contain MCI. Chlorides (MgCI2, NaCI between 0.01 – 1%, CuCI up to 1%, CaCI2 from 5% to saturation). Any fluid that will deposit alkaline residue or phosphorous. It is the purchaser’s responsibility to ensure that all fluids in contact with the products are compatible with the construction material of the product, this includes operational fluids and cleaning fluids. Corrosive environments are often a combination of chemical levels, flow rates and temperatures. Failure to ensure this will result in damages to the product. The item “5,000,000 BTU Stainless Steel Tube and Shell Heat Exchanger for Pools/Spas” is in sale since Tuesday, July 9, 2019. This item is in the category “Home & Garden\Yard, Garden & Outdoor Living\Pools & Spas\Pool Equipment & Parts\Pool Heaters & Solar Panels”. The seller is “badger-pipe” and is located in Mauston, Wisconsin. This item can be shipped worldwide.
- Brand: Badger Insulated Pipe
- MPN: Does not apply
- UPC: 689807272478
3,000,000 BTU Stainless Steel Tube and Shell. GPM Boiler Side 90.58. GPM Pool Side 560.16. Boiler Ports 2 1/2 NPT. Pool Ports – 4 NPT. Number of Tubes – 171. PSI Drop Hot 8.32. PSI Drop Cold 8.59. Working Pressure – 80 PSI. BTU rated with 180F Boiler and 80F Pool. This unit is suitable for pools/spas that are 258,000 gallons. These heat exchangers are constructed with a stainless steel 316L shell and stainless steel 316L corrugated inner tubes to ensure high velocities inside the unit. This is a very reliable, efficient and cost effective way to transfer heat indirectly between any boiler circuit and any pool or spa circuit. The units are designed for both horizontal and vertical mounting. Port sizes: (to/from Boiler) 2 1/2″ – (to/from Pool) 4″. It is recommended to always install the unit with the mounting bracket (mounting brackets included with each unit) fixed to a wall, and/or ceiling or floor to prevent water hammer or vibrations which could damage the unit. Always install the Stainless Steel Pool & Spa Heat Exchanger in a counter flow pattern. The units should be installed downstream of the filtration and pumping equipment. The boiler water must be assisted and the usual precautions taken to prevent air locks. The pool water pump should be controlled by a thermostat in the pool pipe work before the heat exchanger and set at the required temperature. Stainless Steel Pool and Spa Heat Exchangers are not suited for saline or salt water environments. For those applications please use one of our Titanium units. For occasional (holidays & weekends) use pools we recommend a 2x output multiplier to obtain a 2°F/hr heat up rate. Nominal values are based on 60°C temperature between incoming heating and heated water. Swimming pools, spas heating – Hot tube heating – Floor heating – Driveway snowmelts. Oil cooling or heating – Steam condenser – District heating – Transmission and engine cooler – Boiler sample cooler – Waste water heat recovery – Industry process applications. The following fluids are prohibited for use as a flushing agent for stainless steel pool and spa heat exchangers. Hydrochloric Acid up to 0.1% concentration. Solutions the contain MCI. Chlorides (MgCI2, NaCI between 0.01 – 1%, CuCI up to 1%, CaCI2 from 5% to saturation). Any fluid that will deposit alkaline residue or phosphorous. It is the purchaser’s responsibility to ensure that all fluids in contact with the products are compatible with the construction material of the product, this includes operational fluids and cleaning fluids. Corrosive environments are often a combination of chemical levels, flow rates and temperatures. Failure to ensure this will result in damages to the product. The item “3,000,000 BTU Stainless Steel Tube and Shell Heat Exchanger for Pools/Spas ss” is in sale since Tuesday, July 9, 2019. This item is in the category “Home & Garden\Yard, Garden & Outdoor Living\Pools & Spas\Pool Equipment & Parts\Pool Heaters & Solar Panels”. The seller is “badger-pipe” and is located in Mauston, Wisconsin. This item can be shipped worldwide.
- Brand: Badger Insulated Pipe
- MPN: Does not apply
- UPC: 689807272447
360,000 BTU Stainless Steel Tube and Shell. GPM Boiler Side 12.63. GPM Pool Side 94.70. Boiler Ports 11/2 NPT. Pool Ports – 2 NPT. Port to Port – 27 13/16. Number of Tubes 36. PSI Drop Cold 2.40. Working Pressure – 80 PSI. BTU rated with 180F Boiler and 80F Pool. This unit is suitable for pools/spas that are 30,960 gallons. These heat exchangers are constructed with a stainless steel 316L shell and stainless steel 316L corrugated inner tubes to ensure high velocities inside the unit. This is a very reliable, efficient and cost effective way to transfer heat indirectly between any boiler circuit and any pool or spa circuit. The units are designed for both horizontal and vertical mounting. Port sizes: (to/from Boiler) 1 1/2″ – (to/from Pool) 2″. It is recommended to always install the unit with the mounting bracket (mounting brackets included with each unit) fixed to a wall, and/or ceiling or floor to prevent water hammer or vibrations which could damage the unit. Always install the Stainless Steel Pool & Spa Heat Exchanger in a counter flow pattern. The units should be installed downstream of the filtration and pumping equipment. The boiler water must be assisted and the usual precautions taken to prevent air locks. The pool water pump should be controlled by a thermostat in the pool pipe work before the heat exchanger and set at the required temperature. Stainless Steel Pool and Spa Heat Exchangers are not suited for saline or salt water environments. For those applications please use one of our Titanium units. For occasional (holidays & weekends) use pools we recommend a 2x output multiplier to obtain a 2°F/hr heat up rate. Nominal values are based on 60°C temperature between incoming heating and heated water. Swimming pools, spas heating – Hot tube heating – Floor heating – Driveway snowmelts. Oil cooling or heating – Steam condenser – District heating – Transmission and engine cooler – Boiler sample cooler – Waste water heat recovery – Industry process applications. The following fluids are prohibited for use as a flushing agent for stainless steel pool and spa heat exchangers. Hydrochloric Acid up to 0.1% concentration. Solutions the contain MCI. Chlorides (MgCI2, NaCI between 0.01 – 1%, CuCI up to 1%, CaCI2 from 5% to saturation). Any fluid that will deposit alkaline residue or phosphorous. It is the purchaser’s responsibility to ensure that all fluids in contact with the products are compatible with the construction material of the product, this includes operational fluids and cleaning fluids. Corrosive environments are often a combination of chemical levels, flow rates and temperatures. Failure to ensure this will result in damages to the product. The item “360,000 BTU Stainless Steel Tube and Shell Heat Exchanger for Pools/Spas ss” is in sale since Tuesday, July 9, 2019. This item is in the category “Home & Garden\Yard, Garden & Outdoor Living\Pools & Spas\Pool Equipment & Parts\Pool Heaters & Solar Panels”. The seller is “badger-pipe” and is located in Mauston, Wisconsin. This item can be shipped to United States.
- MPN: Does not apply
- Brand: Undisclosed
- UPC: 689807256713
300,000 BTU Stainless Steel Tube and Shell. GPM Boiler Side 11.16. GPM Pool Side 86.11. Boiler Ports 11/2 NPT. Pool Ports – 2 NPT. Port to Port – 20 1/2. Number of Tubes – 36. PSI Drop Cold 1.63. Working Pressure – 80 PSI. BTU rated with 180F Boiler and 80F Pool. This unit is suitable for pools/spas that are 25,800 gallons. These heat exchangers are constructed with a stainless steel 316L shell and stainless steel 316L corrugated inner tubes to ensure high velocities inside the unit. This is a very reliable, efficient and cost effective way to transfer heat indirectly between any boiler circuit and any pool or spa circuit. The units are designed for both horizontal and vertical mounting. Port sizes: (to/from Boiler) 1 1/2″ – (to/from Pool) 2″. It is recommended to always install the unit with the mounting bracket (mounting brackets included with each unit) fixed to a wall, and/or ceiling or floor to prevent water hammer or vibrations which could damage the unit. Always install the Stainless Steel Pool & Spa Heat Exchanger in a counter flow pattern. The units should be installed downstream of the filtration and pumping equipment. The boiler water must be assisted and the usual precautions taken to prevent air locks. The pool water pump should be controlled by a thermostat in the pool pipe work before the heat exchanger and set at the required temperature. Stainless Steel Pool and Spa Heat Exchangers are not suited for saline or salt water environments. For those applications please use one of our Titanium units. For occasional (holidays & weekends) use pools we recommend a 2x output multiplier to obtain a 2°F/hr heat up rate. Nominal values are based on 60°C temperature between incoming heating and heated water. Swimming pools, spas heating – Hot tube heating – Floor heating – Driveway snowmelts. Oil cooling or heating – Steam condenser – District heating – Transmission and engine cooler – Boiler sample cooler – Waste water heat recovery – Industry process applications. The following fluids are prohibited for use as a flushing agent for stainless steel pool and spa heat exchangers. Hydrochloric Acid up to 0.1% concentration. Solutions the contain MCI. Chlorides (MgCI2, NaCI between 0.01 – 1%, CuCI up to 1%, CaCI2 from 5% to saturation). Any fluid that will deposit alkaline residue or phosphorous. It is the purchaser’s responsibility to ensure that all fluids in contact with the products are compatible with the construction material of the product, this includes operational fluids and cleaning fluids. Corrosive environments are often a combination of chemical levels, flow rates and temperatures. Failure to ensure this will result in damages to the product. The item “300,000 BTU Stainless Steel Tube and Shell Heat Exchanger for Pools/Spas os” is in sale since Friday, June 28, 2019. This item is in the category “Home & Garden\Yard, Garden & Outdoor Living\Pools & Spas\Pool Equipment & Parts\Pool Heaters & Solar Panels”. The seller is “badger-pipe” and is located in Mauston, Wisconsin. This item can be shipped worldwide.
- Brand: Badger Insulated Pipe
- MPN: Does not apply
85,000 BTU Stainless Steel Tube and Shell. GPM Boiler Side 8.27. GPM Pool Side 56.22. Boiler Ports 3/4 NPT. Pool Ports 1 NPT. Port to Port – 13 5/8. Number of Tubes – 19. PSI Drop Hot 1.02. PSI Drop Cold 1.28. Working Pressure – 80 PSI. BTU rated with 180F Boiler and 80F Pool. This unit is suitable for pools/spas that are 7,310 gallons. These heat exchangers are constructed with a stainless steel 316L shell and stainless steel 316L corrugated inner tubes to ensure high velocities inside the unit. This is a very reliable, efficient and cost effective way to transfer heat indirectly between any boiler circuit and any pool or spa circuit. The units are designed for both horizontal and vertical mounting. Port sizes: (to/from Boiler) 3/4″ – (to/from Pool) 1″. It is recommended to always install the unit with the mounting bracket (mounting brackets included with each unit) fixed to a wall, and/or ceiling or floor to prevent water hammer or vibrations which could damage the unit. Always install the Stainless Steel Pool & Spa Heat Exchanger in a counter flow pattern. The units should be installed downstream of the filtration and pumping equipment. The boiler water must be assisted and the usual precautions taken to prevent air locks. The pool water pump should be controlled by a thermostat in the pool pipe work before the heat exchanger and set at the required temperature. Stainless Steel Pool and Spa Heat Exchangers are not suited for saline or salt water environments. For those applications please use one of our Titanium units. For occasional (holidays & weekends) use pools we recommend a 2x output multiplier to obtain a 2°F/hr heat up rate. Nominal values are based on 60°C temperature between incoming heating and heated water. Swimming pools, spas heating. Hot tub heating. Oil cooling or heating – Steam condenser – District heating – Transmission and engine cooler – Boiler sample cooler – Waste water heat recovery – Industry process applications. The following fluids are prohibited for use as a flushing agent for stainless steel pool and spa heat exchangers. Hydrochloric Acid up to 0.1% concentration. Solutions the contain MCI. Chlorides (MgCI2, NaCI between 0.01 – 1%, CuCI up to 1%, CaCI2 from 5% to saturation). Any fluid that will deposit alkaline residue or phosphorous. It is the purchaser’s responsibility to ensure that all fluids in contact with the products are compatible with the construction material of the product, this includes operational fluids and cleaning fluids. Corrosive environments are often a combination of chemical levels, flow rates and temperatures. Failure to ensure this will result in damages to the product. The item “85,000 BTU Stainless Steel Tube and Shell Heat Exchanger for Pools/Spas os” is in sale since Thursday, June 20, 2019. This item is in the category “Home & Garden\Yard, Garden & Outdoor Living\Pools & Spas\Pool Equipment & Parts\Pool Heaters & Solar Panels”. The seller is “badger-pipe” and is located in Mauston, Wisconsin. This item can be shipped to United States.
- Brand: Undisclosed
- MPN: Does not apply
- UPC: 689807256829
155,000 BTU Stainless Steel Tube and Shell. GPM Boiler Side 8.46. GPM Pool Side 62.66. Boiler Ports – 1 NPT. Pool Ports – 1 1/2 NPT. Port to Port – 9 1/8. Number of Tubes – 30. PSI Drop Hot 1.10. PSI Drop Cold 1.58. Working Pressure – 80 PSI. BTU rated with 180F Boiler and 80F Pool. This unit is suitable for pools/spas that are 13,330 gallons. These heat exchangers are constructed with a stainless steel 316L shell and stainless steel 316L corrugated inner tubes to ensure high velocities inside the unit. This is a very reliable, efficient and cost effective way to transfer heat indirectly between any boiler circuit and any pool or spa circuit. The units are designed for both horizontal and vertical mounting. Port sizes: (to/from Boiler) 1″ – (to/from Pool) 1 1/2″. It is recommended to always install the unit with the mounting bracket (mounting brackets included with each unit) fixed to a wall, and/or ceiling or floor to prevent water hammer or vibrations which could damage the unit. Always install the Stainless Steel Pool & Spa Heat Exchanger in a counter flow pattern. The units should be installed downstream of the filtration and pumping equipment. The boiler water must be assisted and the usual precautions taken to prevent air locks. The pool water pump should be controlled by a thermostat in the pool pipe work before the heat exchanger and set at the required temperature. Stainless Steel Pool and Spa Heat Exchangers are not suited for saline or salt water environments. For those applications please use one of our Titanium units. For occasional (holidays & weekends) use pools we recommend a 2x output multiplier to obtain a 2°F/hr heat up rate; 2. Nominal values are based on 60°C temperature between incoming heating and heated water. Swimming pools, spas heating – Hot tube heating – Floor heating – Driveway snowmelts. Oil cooling or heating – Steam condenser – District heating – Transmission and engine cooler – Boiler sample cooler – Waste water heat recovery – Industry process applications. The following fluids are prohibited for use as a flushing agent for stainless steel pool and spa heat exchangers. Hydrochloric Acid up to 0.1% concentration. Solutions the contain MCI. Chlorides (MgCI2, NaCI between 0.01 – 1%, CuCI up to 1%, CaCI2 from 5% to saturation). Any fluid that will deposit alkaline residue or phosphorous. It is the purchaser’s responsibility to ensure that all fluids in contact with the products are compatible with the construction material of the product, this includes operational fluids and cleaning fluids. Corrosive environments are often a combination of chemical levels, flow rates and temperatures. Failure to ensure this will result in damages to the product. The item “155,000 BTU Stainless Steel Tube and Shell Heat Exchanger for Pools/Spas os” is in sale since Thursday, June 20, 2019. This item is in the category “Home & Garden\Yard, Garden & Outdoor Living\Pools & Spas\Pool Equipment & Parts\Pool Heaters & Solar Panels”. The seller is “badger-pipe” and is located in Mauston, Wisconsin. This item can be shipped to United States.
- Brand: Undisclosed
- MPN: Does not apply
- UPC: 689807256584
55,000 BTU Titanium Tube and Shell Heat Exchanger for Saltwater Pools / Spas. GPM Boiler Side 7.49. GPM Pool Side 48.84. Boiler Ports 3/4 NPT. Pool Ports – 1 NPT. Port to Port -7 1/2. Number of Tubes – 19. PSI Drop Cold 1.03. Working Pressure – 80 PSI. BTU rated with 180F Boiler and 80F Pool. This unit is suitable for pools/spas that are 4,700 gallons. These heat exchangers are constructed with a Titanium shell and Titanium corrugated inner tubes to ensure high velocities inside the unit. This is a very reliable, efficient and cost effective way to transfer heat indirectly between any boiler circuit and any pool or spa circuit. The units are designed for both horizontal and vertical mounting. Port sizes: (to/from Boiler) 3/4″ – (to/from Pool) 1″. It is recommended to always install the unit with the mounting bracket (mounting brackets included with each unit) fixed to a wall, and/or ceiling or floor to prevent water hammer or vibrations which could damage the unit. Always install the Titanium Pool & Spa Heat Exchanger in a counter flow pattern. The units should be installed downstream of the filtration and pumping equipment. The boiler water must be assisted and the usual precaustions taken to prevent air locks. The pool water pump should be controlled by a thermostat in the pool pipe work before the heat exchanger and set at the required temperature. Titanium Pool and Spa Heat Exchangers are suited for a large range of chemical environments and conditions, due to a thin, invisible, but extremely protective surface oxide film (primarily TiO2). Titanium is especially known for its elevated resistance to localized attack and stress corrosion in aqueous chlorides e. Brines, seawater and other halides and wet halogens e. Wet CI2 or CI2 salt, brines, and to hot, highly oxidizing, acidic solutions e. FeCI3 and nitric acid solutions. Titanium is also recognized for its superior resistance to erosion, erosion-corrosion, cavitations and impingement in flowing, turbulent fluids. 190 PSI (1.31MPa). Swimming Pool Heat Exchangers Nominal Performance. For occasional (holidays & weekends) use pools we recommend a 2x output multiplier to obtain a 2°F/hr heat up rate; 2. Nominal values are based on 60°C temperature between incoming heating and heated water. Quick Selection Reference for swimming pool heat exchangers. Stainless Steel and Titanium Corrosion Resistance Table. Swimming pools, spas heating – Hot tube heating – Floor heating – Driveway snowmelts. Oil cooling or heating – Steam condenser – District heating – Transmission and engine cooler – Boiler sample cooler – Waste water heat recovery – Industry process applications. It is the purchaser’s responsibility to ensure that all fluids in contact with the products are compatible with the construction material of the product, this includes operational fluids and cleaning fluids. Corrosive environments are often a combination of chemical levels, flow rates and temperatures. Failure to ensure this will result in damages to the product. These units are built under our contract, overseas, to our strict standards. You can almost guarantee if you are paying less than double our price it was not manufactured in the US with US workers. The item “55,000 BTU Titanium Tube and Shell Heat Exchanger for Saltwater Pools/Spas os” is in sale since Thursday, June 20, 2019. This item is in the category “Home & Garden\Yard, Garden & Outdoor Living\Pools & Spas\Pool Equipment & Parts\Pool Heaters & Solar Panels”. The seller is “badger-pipe” and is located in Mauston, Wisconsin. This item can be shipped worldwide.
- Brand: Undisclosed
- MPN: Does not apply
- UPC: 689807256768
85,000 BTU Titanium Tube and Shell. GPM Boiler Side 8.27. GPM Pool Side 56.22. Boiler Ports 3/4 NPT. Pool Ports 1 NPT. Port to Port – 13 5/8. Number of Tubes – 19. PSI Drop Hot 1.02. PSI Drop Cold 1.28. Working Pressure – 80 PSI. BTU rated with 180F Boiler and 80F Pool. This unit is suitable for pools/spas that are 7,310 gallons. These heat exchangers are constructed with a Titanium shell and Titanium corrugated inner tubes to ensure high velocities inside the unit. This is a very reliable, efficient and cost effective way to transfer heat indirectly between any boiler circuit and any pool or spa circuit. The units are designed for both horizontal and vertical mounting. Port sizes: (to/from Boiler) 3/4″ – (to/from Pool) 1″. It is recommended to always install the unit with the mounting bracket (mounting brackets included with each unit) fixed to a wall, and/or ceiling or floor to prevent water hammer or vibrations which could damage the unit. Always install the Titanium Pool & Spa Heat Exchanger in a counter flow pattern. The units should be installed downstream of the filtration and pumping equipment. The boiler water must be assisted and the usual precaustions taken to prevent air locks. The pool water pump should be controlled by a thermostat in the pool pipe work before the heat exchanger and set at the required temperature. Titanium Pool and Spa Heat Exchangers are suited for a large range of chemical environments and conditions, due to a thin, invisible, but extremely protective surface oxide film (primarily TiO2). Titanium is especially known for its elevated resistance to localized attack and stress corrosion in aqueous chlorides e. Brines, seawater and other halides and wet halogens e. Wet CI2 or CI2 sat, brines, and to hot, highly oxidizing, acidic solutions e. FeCI3 and nitric acid solutions. Titanium is also recognized for its superior resistance to erosion, erosion-corrosion, cavitations and impingement in flowing, turbulent fluids. For occasional (holidays & weekends) use pools we recommend a 2x output multiplier to obtain a 2°F/hr heat up rate. Nominal values are based on 60°C temperature between incoming heating and heated water. Swimming pools, spas heating – Hot tube heating – Floor heating – Driveway snowmelts. Oil cooling or heating – Steam condenser – District heating – Transmission and engine cooler – Boiler sample cooler – Waste water heat recovery – Industry process applications. It is the purchaser’s responsibility to ensure that all fluids in contact with the products are compatible with the construction material of the product, this includes operational fluids and cleaning fluids. Corrosive environments are often a combination of chemical levels, flow rates and temperatures. Failure to ensure this will result in damages to the product. The item “85,000 BTU Titanium Tube & Shell Heat Exchanger for Saltwater Pools/Spas os” is in sale since Thursday, June 20, 2019. This item is in the category “Home & Garden\Yard, Garden & Outdoor Living\Pools & Spas\Pool Equipment & Parts\Pool Heaters & Solar Panels”. The seller is “badger-pipe” and is located in Mauston, Wisconsin. This item can be shipped worldwide.
- Brand: Undisclosed
- MPN: Does not apply
- UPC: 689807256843
300,000 BTU Titanium Tube and Shell. GPM Boiler Side 11.16. GPM Pool Side 86.11. Boiler Ports 11/2 NPT. Pool Ports – 2 NPT. Port to Port -20 1/2. Number of Tubes – 36. PSI Drop Cold 1.63. Working Pressure – 80 PSI. BTU rated with 180F Boiler and 80F Pool. This unit is suitable for pools/spas that are 25,800 gallons. These heat exchangers are constructed with a Titanium shell and Titanium corrugated inner tubes to ensure high velocities inside the unit. This is a very reliable, efficient and cost effective way to transfer heat indirectly between any boiler circuit and any pool or spa circuit. The units are designed for both horizontal and vertical mounting. Port sizes: (to/from Boiler) 1 1/2″ – (to/from Pool) 2″. It is recommended to always install the unit with the mounting bracket (mounting brackets included with each unit) fixed to a wall, and/or ceiling or floor to prevent water hammer or vibrations which could damage the unit. Always install the Titanium Pool & Spa Heat Exchanger in a counter flow pattern. The units should be installed downstream of the filtration and pumping equipment. The boiler water must be assisted and the usual precaustions taken to prevent air locks. The pool water pump should be controlled by a thermostat in the pool pipe work before the heat exchanger and set at the required temperature. Titanium Pool and Spa Heat Exchangers are suited for a large range of chemical environments and conditions, due to a thin, invisible, but extremely protective surface oxide film (primarily TiO2). Titanium is especially known for its elevated resistance to localized attack and stress corrosion in aqueous chlorides e. Brines, seawater and other halides and wet halogens e. Wet CI2 or CI2 sat, brines, and to hot, highly oxidizing, acidic solutions e. FeCI3 and nitric acid solutions. Titanium is also recognized for its superior resistance to erosion, erosion-corrosion, cavitations and impingement in flowing, turbulent fluids. For occasional (holidays & weekends) use pools we recommend a 2x output multiplier to obtain a 2°F/hr heat up rate; 2. Nominal values are based on 60°C temperature between incoming heating and heated water. Swimming pools, spas heating – Hot tube heating – Floor heating – Driveway snowmelts. Oil cooling or heating – Steam condenser – District heating – Transmission and engine cooler – Boiler sample cooler – Waste water heat recovery – Industry process applications. It is the purchaser’s responsibility to ensure that all fluids in contact with the products are compatible with the construction material of the product, this includes operational fluids and cleaning fluids. Corrosive environments are often a combination of chemical levels, flow rates and temperatures. Failure to ensure this will result in damages to the product. The item “300k BTU Titanium Tube and Shell Heat Exchanger for Saltwater Pools/Spas ss” is in sale since Thursday, June 20, 2019. This item is in the category “Home & Garden\Yard, Garden & Outdoor Living\Pools & Spas\Pool Equipment & Parts\Pool Heaters & Solar Panels”. The seller is “badger-pipe” and is located in Mauston, Wisconsin. This item can be shipped to United States.
- Brand: Undisclosed
- MPN: Does not apply
- UPC: 689807256690
210,000 BTU Stainless Steel Tube and Shell Heat Exchanger for Pools/Spas os. 210,000 BTU Stainless Steel Tube and Shell Opposite Side Ports GPM Boiler Side 9.13 GPM Pool Side 63.94 Boiler Ports 11/2″ NPT Pool Ports – 1 1/2″ NPT Port to Port – 13 1/4″ Diameter 3 3/16″” Length 20″ Number of Tubes – 30 PSI Drop Hot. 38 PSI Drop Cold 1.06 Working Pressure – 80 PSI BTU rated with 180F Boiler and 80F Pool This unit is suitable for pools/spas that are 18,060 gallons. These heat exchangers are constructed with a stainless steel 316L shell and stainless steel 316L corrugated inner tubes to ensure high velocities inside the unit. This is a very reliable, efficient and cost effective way to transfer heat indirectly between any boiler circuit and any pool or spa circuit. The units are designed for both horizontal and vertical mounting. Port sizes: (to/from Boiler) 1 1/2″ – (to/from Pool) 1 1/2″. It is recommended to always install the unit with the mounting bracket (mounting brackets included with each unit) fixed to a wall, and/or ceiling or floor to prevent water hammer or vibrations which could damage the unit. Always install the Stainless Steel Pool & Spa Heat Exchanger in a counter flow pattern. The units should be installed downstream of the filtration and pumping equipment. The boiler water must be assisted and the usual precautions taken to prevent air locks. The pool water pump should be controlled by a thermostat in the pool pipe work before the heat exchanger and set at the required temperature. Stainless Steel Pool and Spa Heat Exchangers are not suited for saline or salt water environments. For those applications please use one of our Titanium units. For occasional (holidays & weekends) use pools we recommend a 2x output multiplier to obtain a 2°F/hr heat up rate;2. Nominal values are based on 60°C temperature between incoming heating and heated water. Typical residential application: – Swimming pools, spas heating- Hot tube heating- Floor heating- Driveway snowmelts Typical industrial application: – Oil cooling or heating- Steam condenser- District heating- Transmission and engine cooler- Boiler sample cooler- Waste water heat recovery- Industry process applications IMPORTANT!! The following fluids are prohibited for use as a flushing agent for stainless steel pool and spa heat exchangers: Hydrochloric Acid up to 0.1% concentration Solutions the contain MCI Chlorides (MgCI2, NaCI between 0.01 – 1%, CuCI up to 1%, CaCI2 from 5% to saturation) Any fluid that will deposit alkaline residue or phosphorous It is the purchaser’s responsibility to ensure that all fluids in contact with the products are compatible with the construction material of the product, this includes operational fluids and cleaning fluids. Corrosive environments are often a combination of chemical levels, flow rates and temperatures. Failure to ensure this will result in damages to the product. 210,000 BTU Stainless Steel Tube and Shell. GPM Boiler Side 9.13. GPM Pool Side 63.94. Boiler Ports 11/2 NPT. Pool Ports – 1 1/2 NPT. Port to Port – 13 1/4. Number of Tubes – 30. PSI Drop Cold 1.06. Working Pressure – 80 PSI. BTU rated with 180F Boiler and 80F Pool. This unit is suitable for pools/spas that are 18,060 gallons. For occasional (holidays & weekends) use pools we recommend a 2x output multiplier to obtain a 2°F/hr heat up rate. Swimming pools, spas heating – Hot tube heating – Floor heating – Driveway snowmelts. Oil cooling or heating – Steam condenser – District heating – Transmission and engine cooler – Boiler sample cooler – Waste water heat recovery – Industry process applications. The following fluids are prohibited for use as a flushing agent for stainless steel pool and spa heat exchangers. Hydrochloric Acid up to 0.1% concentration. Solutions the contain MCI. Chlorides (MgCI2, NaCI between 0.01 – 1%, CuCI up to 1%, CaCI2 from 5% to saturation). Any fluid that will deposit alkaline residue or phosphorous. It is the purchaser’s responsibility to ensure that all fluids in contact with the products are compatible with the construction material of the product, this includes operational fluids and cleaning fluids. The item “210,000 BTU Stainless Steel Tube and Shell Heat Exchanger for Pools/Spas os” is in sale since Thursday, June 20, 2019. This item is in the category “Home & Garden\Yard, Garden & Outdoor Living\Pools & Spas\Pool Equipment & Parts\Pool Heaters & Solar Panels”. The seller is “badger-pipe” and is located in Mauston, Wisconsin. This item can be shipped worldwide.
- Brand: Badger Insulated Pipe
- MPN: Does Not Apply