155,000 BTU Titanium Tube and Shell. GPM Boiler Side 8.46. GPM Pool Side 62.66. Boiler Ports – 1 NPT. Pool Ports – 1 1/2 NPT. Port to Port – 9 1/8. Number of Tubes – 30. PSI Drop Hot 1.10. PSI Drop Cold 1.58. Working Pressure – 80 PSI. BTU rated with 180F Boiler and 80F Pool. This unit is suitable for pools/spas that are 13,330 gallons. These heat exchangers are constructed with a Titanium shell and Titanium corrugated inner tubes to ensure high velocities inside the unit. This is a very reliable, efficient and cost effective way to transfer heat indirectly between any boiler circuit and any pool or spa circuit. The units are designed for both horizontal and vertical mounting. Port sizes: (to/from Boiler) 1″ – (to/from Pool) 1 1/2″. It is recommended to always install the unit with the mounting bracket (mounting brackets included with each unit) fixed to a wall, and/or ceiling or floor to prevent water hammer or vibrations which could damage the unit. Always install the Titanium Pool & Spa Heat Exchanger in a counter flow pattern. The units should be installed downstream of the filtration and pumping equipment. The boiler water must be assisted and the usual precaustions taken to prevent air locks. The pool water pump should be controlled by a thermostat in the pool pipe work before the heat exchanger and set at the required temperature. Titanium Pool and Spa Heat Exchangers are suited for a large range of chemical environments and conditions, due to a thin, invisible, but extremely protective surface oxide film (primarily TiO2). Titanium is especially known for its elevated resistance to localized attack and stress corrosion in aqueous chlorides e. Brines, seawater and other halides and wet halogens e. Wet CI2 or CI2 sat, brines, and to hot, highly oxidizing, acidic solutions e. FeCI3 and nitric acid solutions. Titanium is also recognized for its superior resistance to erosion, erosion-corrosion, cavitations and impingement in flowing, turbulent fluids. For occasional (holidays & weekends) use pools we recommend a 2x output multiplier to obtain a 2°F/hr heat up rate. Nominal values are based on 60°C temperature between incoming heating and heated water. Swimming pools, spas heating – Hot tube heating – Floor heating – Driveway snowmelts. Oil cooling or heating – Steam condenser – District heating – Transmission and engine cooler – Boiler sample cooler – Waste water heat recovery – Industry process applications. It is the purchaser’s responsibility to ensure that all fluids in contact with the products are compatible with the construction material of the product, this includes operational fluids and cleaning fluids. Corrosive environments are often a combination of chemical levels, flow rates and temperatures. Failure to ensure this will result in damages to the product. The item “155k BTU Titanium Tube and Shell Heat Exchanger for Saltwater Pools/Spas os” is in sale since Thursday, June 20, 2019. This item is in the category “Home & Garden\Yard, Garden & Outdoor Living\Pools & Spas\Pool Equipment & Parts\Pool Heaters & Solar Panels”. The seller is “badger-pipe” and is located in Mauston, Wisconsin. This item can be shipped worldwide.
- Brand: Undisclosed
- MPN: Does not apply
- UPC: 689807256607
- Type: Heat Exchanger
Product description: The swimming pool heat exchanger is made of high-grade anticorrosive stainless steel, which has the characteristics of anti-rust and salt water resistance, so it is very durable and very suitable for chlorine or salt water swimming pools and spas. 1 1/2″ FPT is used on one side of the swimming pool water, and 1″ FPT is used for hot water. The salt pond heat exchanger adopts an innovative in-line design to ensure a continuous constant temperature and indirectly transfer heat between any hot water circuit, steam circuit and any swimming pool or spa facility. The shell-and-tube heat exchanger is based on the 60°C (140°F) temperature difference between the inlet and hot water, and can provide a fresh pond of 200 kBtu/hr. It gets hot immediately without waiting. Welcome to my store. The swimming pool heat exchanger is made of high-grade anticorrosive stainless steel, which has the characteristics of anti-rust and salt water resistance, so it is very durable and very suitable for chlorine or salt water swimming pools and spas. This kind of heat exchanger is a very safe, reliable, efficient and cost-effective way to heat swimming pools or spas through any hydraulic system. The heat recovery pool heater is very suitable for swimming pools, spas, hot tubs, solar, hydraulic heating, oil cooling, heat recovery, snow melting, etc. Material: 304 stainless steel. Heat transfer area: 4.8 square feet. Hot water flow rate: 30 L/min. Cold water flow: 250 L/min. Side of hot water pipe: 1 FPT. Same side port: 1 1/2 FPT. 1 x stainless steel heat exchanger. 2 x fixed bracket. Feedback is very important to us. It is impossible to address issues if we do not know about them! Faction is our ultimate goal. We work hard to earn your trust and future business. A If you receive a defective item, you may return it or ask for a discount. Due to time zones, our reply to your questions may not be immediately. If it’s non-workdays, please kindly be patient and wait till Monday. The item “200 kBtu Stainless Steel Tube and Shell Heat Exchanger For Pools/Spas Same Side” is in sale since Wednesday, March 17, 2021. This item is in the category “Home & Garden\Yard, Garden & Outdoor Living\Pools & Spas\Pool Equipment & Parts\Pool Heaters & Solar Panels”. The seller is “galaxyond” and is located in Monroe Township, New Jersey. This item can be shipped to United States.
- BTUh Heating Rating: 200 kBtu
- Tank Capacity: N/A
- Heating System: N/A
- Voltage: N/A
- Amperage: N/A
- Model: N/A
- Features: N/A
- Water Temperature Range: N/A
- Power: N/A
- Suitable For: Hot Tubs
- Type: ppol heat exchanger
- Brand: Unbranded
- MPN: Does Not Apply
- Material: 304 stainless steel
- Same Side Ports: 1 1/2″ FPT
- Weight: 11.5lbs(5.2kg)
- Power Source: Gas / Wood / Solar / Heat Pump / Electricity
- Output: 200 kBtu/hour
- Hot Water flow rate: 30 L/min
- Cold water flow: 250 L/min
- Side of hot water pipe: 1″ FPT
- Country/Region of Manufacture: China
- Heat transfer area: 4.8 square feet
- Packing size: 54*19*19cm
Product description: The swimming pool heat exchanger is made of high-grade anticorrosive stainless steel, which has the characteristics of anti-rust and salt water resistance, so it is very durable and very suitable for chlorine or salt water swimming pools and spas. 1 1/2″ FPT is used on one side of the swimming pool water, and 1″ FPT is used for hot water. The salt pond heat exchanger adopts an innovative in-line design to ensure a continuous constant temperature and indirectly transfer heat between any hot water circuit, steam circuit and any swimming pool or spa facility. The shell-and-tube heat exchanger is based on the 60°C (140°F) temperature difference between the inlet and hot water, and can provide a fresh pond of 200 kBtu/hr. It gets hot immediately without waiting. You may also like. 200 kBtu For Pools/Spas Same Side Stainless Steel Heat Exchanger Tube and Shell. The swimming pool heat exchanger is made of high-grade anticorrosive stainless steel, which has the characteristics of anti-rust and salt water resistance, so it is very durable and very suitable for chlorine or salt water swimming pools and spas. This kind of heat exchanger is a very safe, reliable, efficient and cost-effective way to heat swimming pools or spas through any hydraulic system. The heat recovery pool heater is very suitable for swimming pools, spas, hot tubs, solar, hydraulic heating, oil cooling, heat recovery, snow melting, etc. Material: 304 stainless steel. Heat transfer area: 4.8 square feet. Hot water flow rate: 30 L/min. Cold water flow: 250 L/min. Side of hot water pipe: 1 FPT. Same side port: 1 1/2 FPT. 1 x stainless steel heat exchanger. 2 x fixed bracket. Feedback is very important to us. It is impossible to address issues if we do not know about them! Faction is our ultimate goal. We work hard to earn your trust and future business. A If you receive a defective item, you may return it or ask for a discount. Due to time zones, our reply to your questions may not be immediately. If it’s non-workdays, please kindly be patient and wait till Monday. The item “200kBtu For Pools/Spas Same Side Stainless Steel Heat Exchanger Tube and Shell” is in sale since Thursday, July 29, 2021. This item is in the category “Home & Garden\Yard, Garden & Outdoor Living\Pools & Spas\Pool Equipment & Parts\Pool Heaters & Solar Panels”. The seller is “yiyibushe-4″ and is located in Monroe Township, New Jersey. This item can be shipped to United States.
- Features: Good quality guarantee
- Energy Star: Not Compliant
- Type: ppol heat exchanger
- Brand: Unbranded
- MPN: Does Not Apply
- Material: 304 stainless steel
- Same Side Ports: 1 1/2″ FPT
- Weight: 11.5lbs(5.2kg)
- Power Source: Gas / Wood / Solar / Heat Pump / Electricity
- Output: 200 kBtu/hour
- Hot Water flow rate: 30 L/min
- Cold water flow: 250 L/min
- Side of hot water pipe: 1″ FPT
- Country/Region of Manufacture: China
- Heat transfer area: 4.8 square feet
- Packing size: 54*19*19cm
- Suitable For: swimming pools, spas, hot tubs
- Voltage: Does not apply
- Model: Does not apply
- BTUh Heating Rating: 200 kBtu
- Heating System: any hydraulic system.
- Amperage: Does not apply
- Power: Does not apply
- Tank Capacity: Hot water flow rate: 30 L/min,Cold water flow: 250 L/min
- Water Temperature Range: 60°C (140°F) temperature difference
210,000 BTU Titanium Tube and Shell. GPM Boiler Side 9.13. GPM Pool Side 63.94. Boiler Ports 11/2 NPT. Pool Ports – 1 1/2 NPT. Port to Port – 13 1/4. Number of Tubes – 30. PSI Drop Cold 1.06. Working Pressure – 80 PSI. BTU rated with 180F Boiler and 80F Pool. This unit is suitable for pools/spas that are 18,060 gallons. These heat exchangers are constructed with a Titanium shell and Titanium corrugated inner tubes to ensure high velocities inside the unit. This is a very reliable, efficient and cost effective way to transfer heat indirectly between any boiler circuit and any pool or spa circuit. The units are designed for both horizontal and vertical mounting. Port sizes: (to/from Boiler) 1 1/2″ – (to/from Pool) 1 1/2″. It is recommended to always install the unit with the mounting bracket (mounting brackets included with each unit) fixed to a wall, and/or ceiling or floor to prevent water hammer or vibrations which could damage the unit. Always install the Titanium Pool & Spa Heat Exchanger in a counter flow pattern. The units should be installed downstream of the filtration and pumping equipment. The boiler water must be assisted and the usual precaustions taken to prevent air locks. The pool water pump should be controlled by a thermostat in the pool pipe work before the heat exchanger and set at the required temperature. Titanium Pool and Spa Heat Exchangers are suited for a large range of chemical environments and conditions, due to a thin, invisible, but extremely protective surface oxide film (primarily TiO2). Titanium is especially known for its elevated resistance to localized attack and stress corrosion in aqueous chlorides e. Brines, seawater and other halides and wet halogens e. Wet CI2 or CI2 sat, brines, and to hot, highly oxidizing, acidic solutions e. FeCI3 and nitric acid solutions. Titanium is also recognized for its superior resistance to erosion, erosion-corrosion, cavitations and impingement in flowing, turbulent fluids. For occasional (holidays & weekends) use pools we recommend a 2x output multiplier to obtain a 2°F/hr heat up rate; – Hot tube heating – Floor heating – Driveway snowmelts. Oil cooling or heating – Steam condenser – District heating – Transmission and engine cooler – Boiler sample cooler – Waste water heat recovery – Industry process applications. It is the purchaser’s responsibility to ensure that all fluids in contact with the products are compatible with the construction material of the product, this includes operational fluids and cleaning fluids. Corrosive environments are often a combination of chemical levels, flow rates and temperatures. Failure to ensure this will result in damages to the product. The item “210k BTU Titanium Tube and Shell Heat Exchanger for Saltwater Pools/Spas ss” is in sale since Thursday, June 20, 2019. This item is in the category “Home & Garden\Yard, Garden & Outdoor Living\Pools & Spas\Pool Equipment & Parts\Pool Heaters & Solar Panels”. The seller is “badger-pipe” and is located in Mauston, Wisconsin. This item can be shipped worldwide.
- Brand: Undisclosed
- MPN: Does not apply
2,400,000 BTU Stainless Steel Tube and Shell. Boiler Ports 2 1/2 NPT. Pool Ports -4 NPT. Number of Tubes – 171. Working Pressure – 80 PSI. BTU rated with 180F Boiler and 80F Pool. This unit is suitable for pools/spas that are 211,200 gallons. These heat exchangers are constructed with a stainless steel 316L shell and stainless steel 316L corrugated inner tubes to ensure high velocities inside the unit. This is a very reliable, efficient and cost effective way to transfer heat indirectly between any boiler circuit and any pool or spa circuit. The units are designed for both horizontal and vertical mounting. Port sizes: (to/from Boiler) 2 1/2″ – (to/from Pool) 4″. It is recommended to always install the unit with the mounting bracket (mounting brackets included with each unit) fixed to a wall, and/or ceiling or floor to prevent water hammer or vibrations which could damage the unit. Always install the Stainless Steel Pool & Spa Heat Exchanger in a counter flow pattern. The units should be installed downstream of the filtration and pumping equipment. The boiler water must be assisted and the usual precautions taken to prevent air locks. The pool water pump should be controlled by a thermostat in the pool pipe work before the heat exchanger and set at the required temperature. Stainless Steel Pool and Spa Heat Exchangers are not suited for saline or salt water environments. For those applications please use one of our Titanium units. For occasional (holidays & weekends) use pools we recommend a 2x output multiplier to obtain a 2°F/hr heat up rate; 2. Nominal values are based on 60°C temperature between incoming heating and heated water. Swimming pools, spas heating – Hot tube heating – Floor heating – Driveway snowmelts. Oil cooling or heating – Steam condenser – District heating – Transmission and engine cooler – Boiler sample cooler – Waste water heat recovery – Industry process applications. The following fluids are prohibited for use as a flushing agent for stainless steel pool and spa heat exchangers. Hydrochloric Acid up to 0.1% concentration. Solutions the contain MCI. Chlorides (MgCI2, NaCI between 0.01 – 1%, CuCI up to 1%, CaCI2 from 5% to saturation). Any fluid that will deposit alkaline residue or phosphorous. It is the purchaser’s responsibility to ensure that all fluids in contact with the products are compatible with the construction material of the product, this includes operational fluids and cleaning fluids. Corrosive environments are often a combination of chemical levels, flow rates and temperatures. Failure to ensure this will result in damages to the product. The item “2,400,000 BTU Stainless Steel Tube and Shell Heat Exchanger for Pools/Spas ss” is in sale since Tuesday, July 9, 2019. This item is in the category “Home & Garden\Yard, Garden & Outdoor Living\Pools & Spas\Pool Equipment & Parts\Pool Heaters & Solar Panels”. The seller is “badger-pipe” and is located in Mauston, Wisconsin. This item can be shipped worldwide.
- Brand: Badger Insulated Pipe
- MPN: Does not apply
1,200,000 BTU Titanium Tube and Shell. GPM Boiler Side – 30.19. GPM Pool Side – 224.06. Boiler Ports – 2 NPT. Pool Ports – 2 1/2 NPT. Port to Port – 35 13/16. Diameter – 5 1/8. Length – 34 13/16. Number of Tubes – 84. PSI Drop Hot – 2.21. PSI Drop Cold – 4.05. Working Pressure – 80 PSI. BTU rated with 180F Boiler and 80F Pool. This unit is suitable for pools/spas that are 103,200 gallons. These heat exchangers are constructed with a Titanium shell and Titanium corrugated inner tubes to ensure high velocities inside the unit. This is a very reliable, efficient and cost effective way to transfer heat indirectly between any boiler circuit and any pool or spa circuit. The units are designed for both horizontal and vertical mounting. Port sizes: (to/from Boiler) 2″ – (to/from Pool) 2 1/2″. It is recommended to always install the unit with the mounting bracket (mounting brackets included with each unit) fixed to a wall, and/or ceiling or floor to prevent water hammer or vibrations which could damage the unit. Always install the Titanium Pool & Spa Heat Exchanger in a counter flow pattern. The units should be installed downstream of the filtration and pumping equipment. The boiler water must be assisted and the usual precaustions taken to prevent air locks. The pool water pump should be controlled by a thermostat in the pool pipe work before the heat exchanger and set at the required temperature. Titanium Pool and Spa Heat Exchangers are suited for a large range of chemical environments and conditions, due to a thin, invisible, but extremely protective surface oxide film (primarily TiO2). Titanium is especially known for its elevated resistance to localized attack and stress corrosion in aqueous chlorides e. Brines, seawater and other halides and wet halogens e. Wet CI2 or CI2 salt, brines, and to hot, highly oxidizing, acidic solutions e. FeCI3 and nitric acid solutions. Titanium is also recognized for its superior resistance to erosion, erosion-corrosion, cavitations and impingement in flowing, turbulent fluids. For occasional (holidays & weekends) use pools we recommend a 2x output multiplier to obtain a 2°F/hr heat up rate; 2. Nominal values are based on 60°C temperature between incoming heating and heated water. Swimming pools, spas heating – Hot tube heating – Floor heating – Driveway snowmelts. Oil cooling or heating – Steam condenser – District heating – Transmission and engine cooler – Boiler sample cooler – Waste water heat recovery – Industry process applications. It is the purchaser’s responsibility to ensure that all fluids in contact with the products are compatible with the construction material of the product, this includes operational fluids and cleaning fluids. Corrosive environments are often a combination of chemical levels, flow rates and temperatures. Failure to ensure this will result in damages to the product. The item “1200k BTU Titanium Tube and Shell Heat Exchanger for Saltwater Pools/Spas ss” is in sale since Thursday, June 20, 2019. This item is in the category “Home & Garden\Yard, Garden & Outdoor Living\Pools & Spas\Pool Equipment & Parts\Pool Heaters & Solar Panels”. The seller is “badger-pipe” and is located in Mauston, Wisconsin. This item can be shipped worldwide.
- Brand: Undisclosed
- MPN: Does not apply
- UPC: 689807256577
You may also like. 200 kBtu Shell&Tube Heat Exchanger for Salt Water/Swimming Pools/spas 304 Steel. The swimming pool heat exchanger is made of high-grade anti-corrosion stainless steel, which has the characteristics of anti-rust and salt water resistance, so it is very durable and very suitable for chlorine or salt water swimming pools and spas. The opposite side of the pool water is 1 1/2″ FPT, and the hot water is 1″ FPT. The salt pond heat exchanger adopts an innovative in-line design to ensure a continuous constant temperature and indirectly transfer heat between any hot water circuit, steam circuit and any swimming pool or spa facility. The shell-and-tube heat exchanger is based on the 60°C (140°F) temperature difference between the inlet and hot water, and can provide a fresh pond of 200 kBtu/hr. It gets hot immediately without waiting. This kind of heat exchanger is a very safe, reliable, efficient and cost-effective way to heat swimming pools or spas through any hydraulic system. The heat recovery pool heater is very suitable for swimming pools, spas, hot tubs, solar, hydraulic heating, oil cooling, heat recovery, snow melting, etc. Material: 304 stainless steel. Heat transfer area: 4.8 square feet. Hot water flow rate: 30 L/min. Cold water flow: 250 L/min. Side of hot water pipe: 1 FPT. Opposite side port: 1 1/2 FPT. 1 x stainless steel heat exchanger. 2 x fixed bracket. Feedback is very important to us. It is impossible to address issues if we do not know about them! Faction is our ultimate goal. We work hard to earn your trust and future business. A If you receive a defective item, you may return it or ask for a discount. Due to time zones, our reply to your questions may not be immediately. If it’s non-workdays, please kindly be patient and wait till Monday. Features: Material: 304 stainless steel Output: 200 kBtu/hour Heat transfer area: 4.8 square feet Hot water flow rate: 30 L/min Cold water flow: 250 L/min Side of hot water pipe: 1″ FPT Opposite side port: 1 1/2″ FPT Packing size: 541919cm Weight: 5.2kg The package includes: 1 x stainless steel heat exchanger 2 x fixed bracket. The item “200 kBtu Shell&Tube Heat Exchanger for Salt Water/Swimming Pools/spas 304 Steel” is in sale since Tuesday, October 27, 2020. This item is in the category “Home & Garden\Yard, Garden & Outdoor Living\Pools & Spas\Pool Equipment & Parts\Pool Heaters & Solar Panels”. The seller is “fast-ship-item” and is located in Rowland Heights, California. This item can be shipped to United States.
- Type: Does not apply
- Brand: Unbranded
- MPN: Does not apply
- Model: Does not apply
- Material: 304 stainless steel
- Output:: 200 kBtu/hour
- Heat transfer area: 4.8 square feet
- Hot water flow rate: 30 L/min
- Cold water flow: 250L/min
- Side of hot water pipe: 1″ FPT
- Opposite side port: 1 1/2″ FPT
- Packing size: 54*19*19cm
- Weight: 5.2kg
55,000 BTU Titanium Tube and Shell. GPM Boiler Side 7.49. GPM Pool Side 48.84. Boiler Ports 3/4 NPT. Pool Ports – 1 NPT. Port to Port -7 1/2. Number of Tubes – 19. PSI Drop Cold 1.03. Working Pressure – 80 PSI. BTU rated with 180F Boiler and 80F Pool. This unit is suitable for pools/spas that are 4,730 gallons. These heat exchangers are constructed with a Titanium shell and Titanium corrugated inner tubes to ensure high velocities inside the unit. This is a very reliable, efficient and cost effective way to transfer heat indirectly between any boiler circuit and any pool or spa circuit. The units are designed for both horizontal and vertical mounting. Port sizes: (to/from Boiler) 3/4″ – (to/from Pool)1″. It is recommended to always install the unit with the mounting bracket (mounting brackets included with each unit) fixed to a wall, and/or ceiling or floor to prevent water hammer or vibrations which could damage the unit. Always install the Titanium Pool & Spa Heat Exchanger in a counter flow pattern. The units should be installed downstream of the filtration and pumping equipment. The boiler water must be assisted and the usual precaustions taken to prevent air locks. Titanium Pool and Spa Heat Exchangers are suited for a large range of chemical environments and conditions, due to a thin, invisible, but extremely protective surface oxide film (primarily TiO2). Titanium is especially known for its elevated resistance to localized attack and stress corrosion in aqueous chlorides e. Brines, seawater and other halides and wet halogens e. Wet CI2 or CI2 sat, brines, and to hot, highly oxidizing, acidic solutions e. FeCI3 and nitric acid solutions. Titanium is also recognized for its superior resistance to erosion, erosion-corrosion, cavitations and impingement in flowing, turbulent fluids. For occasional (holidays & weekends) use pools we recommend a 2x output multiplier to obtain a 2°F/hr heat up rate. Nominal values are based on 60°C temperature between incoming heating and heated water. Swimming pools, spas heating – Hot tube heating – Floor heating – Driveway snowmelts. Oil cooling or heating – Steam condenser – District heating – Transmission and engine cooler – Boiler sample cooler – Waste water heat recovery – Industry process applications. It is the purchaser’s responsibility to ensure that all fluids in contact with the products are compatible with the construction material of the product, this includes operational fluids and cleaning fluids. Corrosive environments are often a combination of chemical levels, flow rates and temperatures. Failure to ensure this will result in damages to the product. The item “55k BTU Titanium Tube and Shell Heat Exchanger for Saltwater Pools/Spas ss” is in sale since Thursday, June 20, 2019. This item is in the category “Home & Garden\Yard, Garden & Outdoor Living\Pools & Spas\Pool Equipment & Parts\Pool Heaters & Solar Panels”. The seller is “badger-pipe” and is located in Mauston, Wisconsin. This item can be shipped worldwide.
- Brand: Undisclosed
- MPN: Does not apply
- UPC: 689807256775
600,000 BTU Stainless Steel Tube and Shell. GPM Boiler Side 17.44. GPM Pool Side 114.16. Boiler Ports 2 NPT. Pool Ports 21/2 NPT. Port to Port – 25 3/8. Number of Tubes – 42. PSI Drop Hot 1.22. PSI Drop Cold 3.07. Working Pressure – 80 PSI. BTU rated with 180F Boiler and 80F Pool. This unit is suitable for pools/spas that are 51,600 gallons. These heat exchangers are constructed with a stainless steel 316L shell and stainless steel 316L corrugated inner tubes to ensure high velocities inside the unit. This is a very reliable, efficient and cost effective way to transfer heat indirectly between any boiler circuit and any pool or spa circuit. The units are designed for both horizontal and vertical mounting. Port sizes: (to/from Boiler) 2″ – (to/from Pool) 2 1/2″. It is recommended to always install the unit with the mounting bracket (mounting brackets included with each unit) fixed to a wall, and/or ceiling or floor to prevent water hammer or vibrations which could damage the unit. Always install the Stainless Steel Pool & Spa Heat Exchanger in a counter flow pattern. The units should be installed downstream of the filtration and pumping equipment. The boiler water must be assisted and the usual precautions taken to prevent air locks. The pool water pump should be controlled by a thermostat in the pool pipe work before the heat exchanger and set at the required temperature. Stainless Steel Pool and Spa Heat Exchangers are not suited for saline or salt water environments. For those applications please use one of our Titanium units. For occasional (holidays & weekends) use pools we recommend a 2x output multiplier to obtain a 2°F/hr heat up rate; 2. Nominal values are based on 60°C temperature between incoming heating and heated water. Swimming pools, spas heating – Hot tube heating – Floor heating – Driveway snowmelts. Oil cooling or heating – Steam condenser – District heating – Transmission and engine cooler – Boiler sample cooler – Waste water heat recovery – Industry process applications. The following fluids are prohibited for use as a flushing agent for stainless steel pool and spa heat exchangers. Hydrochloric Acid up to 0.1% concentration. Solutions the contain MCI. Chlorides (MgCI2, NaCI between 0.01 – 1%, CuCI up to 1%, CaCI2 from 5% to saturation). Any fluid that will deposit alkaline residue or phosphorous. It is the purchaser’s responsibility to ensure that all fluids in contact with the products are compatible with the construction material of the product, this includes operational fluids and cleaning fluids. Corrosive environments are often a combination of chemical levels, flow rates and temperatures. Failure to ensure this will result in damages to the product. The item “600,000 BTU Stainless Steel Tube and Shell Heat Exchanger for Pools/Spas os” is in sale since Thursday, June 20, 2019. This item is in the category “Home & Garden\Yard, Garden & Outdoor Living\Pools & Spas\Pool Equipment & Parts\Pool Heaters & Solar Panels”. The seller is “badger-pipe” and is located in Mauston, Wisconsin. This item can be shipped worldwide.
- Brand: Badger Insulated Pipe
- MPN: Does Not Apply
55,000 BTU Stainless Steel Tube and Shell. GPM Boiler Side 7.49. GPM Pool Side 48.84. Boiler Ports 3/4 NPT. Pool Ports – 1 NPT. Port to Port – 7 1/2. Number of Tubes – 19. PSI Drop Cold 1.03. Working Pressure – 80 PSI. BTU rated with 180F Boiler and 80F Pool. This unit is suitable for pools/spas that are 4,730 gallons. These heat exchangers are constructed with a stainless steel 316L shell and stainless steel 316L corrugated inner tubes to ensure high velocities inside the unit. This is a very reliable, efficient and cost effective way to transfer heat indirectly between any boiler circuit and any pool or spa circuit. The units are designed for both horizontal and vertical mounting. Port sizes: (to/from Boiler) 3/4″- (to/from Pool) 1 “. It is recommended to always install the unit with the mounting bracket (mounting brackets included with each unit) fixed to a wall, and/or ceiling or floor to prevent water hammer or vibrations which could damage the unit. Always install the Stainless Steel Pool & Spa Heat Exchanger in a counter flow pattern. The units should be installed downstream of the filtration and pumping equipment. The boiler water must be assisted and the usual precautions taken to prevent air locks. The pool water pump should be controlled by a thermostat in the pool pipe work before the heat exchanger and set at the required temperature. Stainless Steel Pool and Spa Heat Exchangers are not suited for saline or salt water environments. For those applications please use one of our Titanium units. For occasional (holidays & weekends) use pools we recommend a 2x output multiplier to obtain a 2°F/hr heat up rate; 2. Nominal values are based on 60°C temperature between incoming heating and heated water. Swimming pools, spas heating – Hot tube heating – Floor heating – Driveway snowmelts. Oil cooling or heating – Steam condenser – District heating – Transmission and engine cooler – Boiler sample cooler – Waste water heat recovery – Industry process applications. The following fluids are prohibited for use as a flushing agent for stainless steel pool and spa heat exchangers. Hydrochloric Acid up to 0.1% concentration. Solutions the contain MCI. Chlorides (MgCI2, NaCI between 0.01 – 1%, CuCI up to 1%, CaCI2 from 5% to saturation). Any fluid that will deposit alkaline residue or phosphorous. It is the purchaser’s responsibility to ensure that all fluids in contact with the products are compatible with the construction material of the product, this includes operational fluids and cleaning fluids. Corrosive environments are often a combination of chemical levels, flow rates and temperatures. Failure to ensure this will result in damages to the product. The item “55k BTU Stainless Steel Tube and Shell Heat Exchanger for Pools/Spas os” is in sale since Thursday, June 20, 2019. This item is in the category “Home & Garden\Yard, Garden & Outdoor Living\Pools & Spas\Pool Equipment & Parts\Pool Heaters & Solar Panels”. The seller is “badger-pipe” and is located in Mauston, Wisconsin. This item can be shipped worldwide.
- Brand: Undisclosed
- MPN: Does not apply
- UPC: 689807256744